CONFIG DATE/de

Funktion

Konfiguriert das Format des Datums-Strings für Eingabe und Ausgabe bei BASCOM Datumsfunktionen

 

 

Syntax

CONFIG DATE = DMY , Separator = char

 

 

Anmerkungen

DMY	Die Tag-Monat-Jahr-Reihenfolge. Benutzen Sie DMY, MDY oder YMD.
Char	Das Zeichen, das als Trennzeichen zwischen Tag, Monat und Jahr benutzt werden soll.   Alte Syntax :  / , - oder . (Punkt).   Bevorzugte neue Syntax : MINUS, SLASH oder DOT.   Beispiel: Config Date = DMY, SEPARATOR=MINUS

 

Die folgende Tabelle zeigt die gebräuchlichsten Datumsformate und die entsprechenden Befehle.

 

Country	Format	Statement
American	mm/dd/yy	Config Date = MDY, Separator = SLASH
ANSI	yy.mm.dd	Config Date = YMD, Separator = DOT
Britisch/French	dd/mm/yy	Config Date = DMY, Separator = SLASH
German	dd.mm.yy	Config Date = DMY, Separator = DOT
Italian	dd-mm-yy	Config Date = DMY, Separator = MINUS
Japan/Taiwan	yy/mm/dd	Config Date = YMD, Separator = SLASH
USA	mm-dd-yy	Config Date = MDY, Separator = MINUS

 

 

In Holland würde man folgendes nutzen :

CONFIG DATE = DMY, separator = MINUS

Das würde 24-04-02 für den 24. November 2002 ausgeben.

 

In den USA würde man folgenden benutzen :

CONFIG DATE = MDY , separator = SLASH

Das würde 04/24/02 für den 24.November 2002 ausgeben.

 

 

Siehe auch

CONFIG CLOCK , DATE TIME functions , DayOfWeek , DayOfYear , SecOfDay , SecElapsed , SysDay , SysSec , SysSecElapsed , Time , Date

 

 

Beispiel

'-----------------------------------------------------------------------------------------
'name : megaclock.bas
'copyright : (c) 1995-2005, MCS Electronics
'purpose : shows the new TIME$ and DATE$ reserved variables
'micro : Mega103
'suited for demo : yes
'commercial addon needed : no
'-----------------------------------------------------------------------------------------
 
$regfile = "m103def.dat" ' Mikrocontroller
$crystal = 4000000 ' Taktfrequenz
$baud = 19200 ' Baudrate
$hwstack = 32 ' default use 32 for the hardware stack
$swstack = 10 ' default use 10 for the SW stack
$framesize = 40 ' default use 40 for the frame space
 
'With the 8535 and timer2 or the Mega103 and TIMER0 you can
'easily implement a clock by attaching a 32768 Hz xtal to the timer
'And of course some BASCOM code
 
'This example is written for the STK300 with M103
Enable Interrupts
 
'[configure LCD]
$lcd = &HC000 'address for E and RS
$lcdrs = &H8000 'address for only E
Config Lcd = 20 * 4 'nice display from bg micro
Config Lcdbus = 4 'we run it in bus mode and I hooked up only db4-db7
Config Lcdmode = Bus 'tell about the bus mode
 
'[now init the clock]
Config Date = Mdy , Separator = SLASH ' ANSI-Format
 
Config Clock = Soft 'this is how simple it is
'The above statement will bind in an ISR so you can not use the TIMER anymore!
'For the M103 in this case it means that TIMER0 can not be used by the user anymore
 
'assign the date to the reserved date$
'The format is MM/DD/YY
Date$ = "11/11/00"
 
'assign the time, format in hh:mm:ss military format(24 hours)
'You may not use 1:2:3 !! adding support for this would mean overhead
'But of course you can alter the library routines used
 
Time$ = "02:20:00"
 
'---------------------------------------------------
 
'clear the LCD display
Cls
 
Do
Home 'cursor home
Lcd Date$ ; " " ; Time$ 'show the date and time
Loop
 
'The clock routine does use the following internal variables:
'_day , _month, _year , _sec, _hour, _min
'These are all bytes. You can assign or use them directly
_day = 1
'For the _year variable only the year is stored, not the century
End

Languages	English • Deutsch