Error Codes

The following table lists errors that can occur.

 

Error	Description
1	Unknown statement
2	Unknown structure EXIT statement
3	WHILE expected
4	No more space for IRAM BIT
5	No more space for BIT
6	. expected in filename
7	IF THEN expected
8	BASIC source file not found
9	Maximum 128 aliases allowed
10	Unknown LCD type
11	INPUT, OUTPUT, 0 or 1 expected
12	Unknown CONFIG parameter
13	CONST already specified
14	Only IRAM bytes supported
15	Wrong data type
16	Unknown Definition
17	9 parameters expected
18	BIT only allowed with IRAM or SRAM
19	STRING length expected (DIM S AS STRING * 12 ,for example)
20	Unknown DATA TYPE
21	Out of IRAM space
22	Out of SRAM space
23	Out of XRAM space
24	Out of EPROM space
25	Variable already dimensioned
26	AS expected
27	parameter expected
28	IF THEN expected
29	SELECT CASE expected
30	BIT's are GLOBAL and can not be erased
31	Invalid data type
32	Variable not dimensioned
33	GLOBAL variable can not be ERASED
34	Invalid number of parameters
35	3 parameters expected
36	THEN expected
37	Invalid comparison operator
38	Operation not possible on BITS
39	FOR expected
40	Variable can not be used with RESET
41	Variable can not be used with SET
42	Numeric parameter expected
43	File not found
44	2 variables expected
45	DO expected
46	Assignment error
47	UNTIL expected
50	Value doesn't fit into INTEGER
51	Value doesn't fit into WORD
52	Value doesn't fit into LONG
60	Duplicate label
61	Label not found
62	SUB or FUNCTION expected first
63	Integer or Long expected for ABS()
64	, expected
65	device was not OPEN
66	device already OPENED
68	channel expected
70	BAUD rate not possible
71	Different parameter type passed then declared
72	Getclass error. This is an internal error.
73	Printing this FUNCTION not yet supported
74	3 parameters expected
80	Code does not fit into target chip
81	Use HEX(var) instead of PRINTHEX
82	Use HEX(var) instead of LCDHEX
85	Unknown interrupt source
86	Invalid parameter for TIMER configuration
87	ALIAS already used
88	0 or 1 expected
89	Out of range : must be 1-4
90	Address out of bounds
91	INPUT, OUTPUT, BINARY, or RANDOM expected
92	LEFT or RIGHT expected
93	Variable not dimensioned
94	Too many bits specified
95	Falling or rising expected for edge
96	Pre scale value must be 1,8,64,256 or 1024
97	SUB or FUNCTION must be DECLARED first
98	SET or RESET expected
99	TYPE expected
100	No array support for IRAM variables
101	Can't find HW-register
102	Error in internal routine
103	= expected
104	LoadReg error
105	StoreBit error
106	Unknown register
107	LoadnumValue error
108	Unknown directive in device file
109	= expected in include file for .EQU
110	Include file not found
111	SUB or FUNCTION not DECLARED
112	SUB/FUNCTION name expected
113	SUB/FUNCTION already DECLARED
114	LOCAL only allowed in SUB or FUNCTION
115	channel expected
116	Invalid register file
117	Unknown interrupt
126	NEXT expected.
129	( or ) missing.
200	.DEF not found
201	Low Pointer register expected
202	.EQU not found, probably using functions that are not supported by the selected chip
203	Error in LD or LDD statement
204	Error in ST or STD statement
205	} expected
206	Library file not found
207	Library file already registered
210	Bit definition not found
211	External routine not found
212	LOW LEVEL, RISING or FALLING expected
213	String expected for assignment
214	Size of XRAM string 0
215	Unknown ASM mnemonic
216	CONST not defined
217	No arrays allowed with BIT/BOOLEAN data type
218	Register must be in range from R16-R31
219	INT0-INT3 are always low level triggered in the MEGA
220	Forward jump out of range
221	Backward jump out of range
222	Illegal character
223	expected
224	Index out of range
225	() may not be used with constants
226	Numeric of string constant expected
227	SRAM start greater than SRAM end
228	DATA line must be placed after the END statement
229	End Sub or End Function expected
230	You can not write to a PIN register
231	TO expected
232	Not supported for the selected micro
233	READ only works for normal DATA lines, not for EPROM data
234	') block comment expected first
235	'( block comment expected first
236	Value does not fit into byte
238	Variable is not dimensioned as an array
239	Invalid code sequence because of AVR hardware bug
240	END FUNCTION expected
241	END SUB expected
242	Source variable does not match the target variable
243	Bit index out of range for supplied data type
244	Do not use the Y pointer
245	No arrays supported with IRAM variable
246	No more room for .DEF definitions
247	. expected
248	BYVAL should be used in declaration
249	ISR already defined
250	GOSUB expected
251	Label must be named SECTIC
252	Integer or Word expected
253	ERAM variable can not be used
254	Variable expected
255	Z or Z+ expected
256	Single expected
257	"" expected
258	SRAM string expected
259	- not allowed for a byte
260	Value larger than string length
261	Array expected
262	ON or OFF expected
263	Array index out of range
264	Use ECHO OFF and ECHO ON instead
265	offset expected in LDD or STD like Z+1
266	TIMER0, TIMER1 or TIMER2 expected
267	Numeric constant expected
268	Param must be in range from 0-3
269	END SELECT expected
270	Address already occupied
322	Data type not supported with statement
323	Label too long
324	Chip not supported by I2C slave library
325	Pre-scale value must be 1,8,32,128,256 or 1024
326	ENDIF expected
327	Maximum size is 255
328	Not valid for SW UART
329	FileDateTime can only be assigned to a variable
330	Maximum value for OUT is &H3F
332	$END ASM expected
334	') blockcomment end expected
335	Use before DIM statements
336	Could not set specified CLOCK value
337	No more space for labels
338	AS expected
339	Bytes to read may not be 0.
340	Variable is used as CONSTANT
341	OFFSET Error, contact MCS
342	OFFSET not allowed, too many locals used
343	Variable not supported with this function/statement
344	Program will overwrite bootloader
345	UART not available for the selected micro
346	External interrupt not supported or no settings found in DAT file
347	External interrupt mode not supported or found in DAT file
349	Setting not supported or not found in DAT file
350	Interrupt needs return
351	Not supported yet.
352	ALIAS can not be CONST or DIMMED variable
353	Reserved word may not be used
354	Previous Macro definition must be ended first
355	Macro previously defined
356	String constant size exceeded
357	Too many constants, increase resource languages
358	.DEF error, already defined
359	Operation not allowed on register
360	PRESCALE can not be used in COUNTER mode
361	Member expected
362	SBIC or SBIS was used followed by IN, OUT, SBIC, SBIS, SBI or CBI that also need to be converted.
363	No more room for EPROM DATA Index
364	Name not allowed, is used by constant/variable
365	Function not allowed in PRINT
366	Bit value out or range
367	Function name not allowed
368	Name used by label
369	Duplicate label name used by const or variable
370	Out of Flash memory
371	Function not allowed
372	SE entry missing in DAT file
373	Re-Configuration not allowed
374	. not allowed.
375	Duplicate definition
376	Config not found
377	Unexpected non numeric characters found
378	CAN BAUD not possible
999	DEMO/BETA only supports 4096 bytes of code
9999	Illegal version. Please remove this illegal crack.

 

 

Other error codes are internal ones. Please report them when you get them.

Languages	English • Deutsch