Getting started with Arduino UNO R3 and Ethernet Shield (W5100)

(Difference between revisions)
Jump to: navigation, search
Line 29: Line 29:
 
== Complete Source code:<br/> ==
 
== Complete Source code:<br/> ==
  
 +
<br/><source lang="bascomavr">
 +
 +
' IP Address of Arduino = 192.168.2.254
 +
' Port of Arduino = 1000
 +
' We use UDP
 +
'
 +
 +
'Use Hardware:
 +
' - Arduino UNO R3
 +
' - Arduino Ethernet Shield with W5100 Wiznet Chip
 +
 +
 +
' NTP Server IP address (here you can change the NTP server of your choice)
 +
Const Ntp1 = 192 : Const Ntp2 = 53 : Const Ntp3 = 103 : Const Ntp4 = 108      ' Example =  192.53.103.108
 +
 +
Const Use_ping = 1                                        'use PING NTP server for checking NTP server availability before move on
 +
 +
 +
$regfile = "m328pdef.dat"
 +
$crystal = 16000000                                        '16MHz
 +
$hwstack = 100
 +
$swstack = 100
 +
$framesize = 400
 +
 +
Config Com1 = 57600 , Synchrone = 0 , Parity = None , Stopbits = 1 , Databits = 8 , Clockpol = 0
 +
 +
'-------------------------------------------------------------------------------
 +
' Server Variables
 +
'-------------------------------------------------------------------------------
 +
Dim Ip_sntp_server As Long
 +
'assign the IP number of a SNTP server
 +
Ip_sntp_server = Maketcp(ntp1 , Ntp2 , Ntp3 , Ntp4)        'assign IP of NTP SERVER
 +
 +
 +
 +
Wait 2
 +
Print
 +
Print "-----START Arduino UNO R3 + Ethernet Shield DEMO-----"
 +
'-------------------------------------------------------------------------------
 +
' Network Hardware
 +
'-------------------------------------------------------------------------------
 +
Config Spi = Hard , Interrupt = Off , Data Order = Msb , Master = Yes , Polarity = Low , Phase = 0 , Clockrate = 4 , Noss = 0
 +
Spiinit
 +
 +
Print
 +
Enable Interrupts
 +
 +
  'Here you need MAC address, the ip address you like to use, subnet mask, gateway and localport
 +
  Config Tcpip = Noint , _
 +
            Mac = 1.1.94.127.1.255 , _
 +
            Ip = 192.168.2.254 , _
 +
            Submask = 255.255.255.0 , _
 +
            Gateway = 192.168.2.1 , _
 +
            Localport = 1000 , _
 +
            Tx = $55 , Rx = $55 , _
 +
            Chip = W5100 , _
 +
            Spi = 1
 +
 +
 +
'-------------------------------------------------------------------------------
 +
'  Config Clock
 +
'-------------------------------------------------------------------------------
 +
Dim Local_time As Long
 +
Dim New_second As Bit
 +
 +
Config Date = Dmy , Separator = .
 +
Config Clock = User
 +
 +
Config Timer1 = Timer , Prescale = 256
 +
On Timer1 Timer_irq Saveall                                'the SAVEALL option is NEEDED !
 +
Const Timer_preload = 3036
 +
Enable Timer1
 +
 +
'-------------------------------------------------------------------------------
 +
'  UDP
 +
'-------------------------------------------------------------------------------
 +
Dim Idx As Byte                                            ' socket number
 +
Dim Result As Word                                          ' result
 +
Dim S(255) As Byte
 +
Dim R(255) As Byte
 +
Dim Sstr As String * 255
 +
Dim Temp As Byte , Temp2 As Byte                            ' temp bytes
 +
Dim Ip As Long
 +
 +
'-------------------------------------------------------------------------------
 +
'  PING NTP SERVER to check if NTP server is available
 +
'-------------------------------------------------------------------------------
 +
#if Use_ping = 1
 +
  Dim J As Byte , Res As Byte
 +
  Dim Ii As Byte
 +
  Dim Ping_check_ok As Bit
 +
 +
  ' FILL PING ARRAY
 +
  S(1) = 8                                                    'type is echo
 +
  S(2) = 0                                                    'code
 +
 +
  S(3) = 0                                                    ' for checksum initialization
 +
  S(4) = 0                                                    ' checksum
 +
  S(5) = 0                                                    ' a signature can be any number
 +
  S(6) = 1                                                    '  signature
 +
  S(7) = 0                                                    ' sequence number - any number
 +
  S(8) = 1
 +
  S(9) = 65
 +
 +
  Dim W As Word At S + 2 Overlay                              'same as dta(3) and dta(4)
 +
  Dim B As Byte
 +
  W = Tcpchecksum(s(1) , 9)                                  ' calculate checksum and store in dta(3) and dta(4)
 +
 +
  'Ip = Maketcp(192.53.103.108)                                'try to check this google server
 +
  Print "PING NTP Server : " ; Ip2str(ip_sntp_server)
 +
 +
  'Print "Socket " ; Idx ; " " ; Idx
 +
  Setipprotocol Idx , 1                                      'set protocol to 1
 +
  'the protocol value must be set BEFORE the socket is openend
 +
 +
  Idx = Getsocket(idx , Sock_ipl_raw , 5000 , 0)              'RAW Socket
 +
 +
  ' We try the PING 3 times (but if we get an answer we exit the for loop)
 +
  Do
 +
      Incr Ii
 +
 +
      Result = Udpwrite(ip_sntp_server , 7 , Idx , S(1) , 9)  'write ping data              '
 +
      Print "Ping Number : " ; ii
 +
      Waitms 200                                              ' depending on the hops, speed, etc
 +
      Result = Socketstat(idx , Sel_recv)                      'check for data
 +
    '  Print "REC:" ; Result
 +
      If Result >= 11 Then
 +
 +
        Res = Tcpread(idx , R(1) , Result)                    'get data with TCPREAD !!!
 +
 +
      '    Print "DATA RETURNED :" ; Res
 +
      '(                    '
 +
          For J = 1 To Result
 +
            Print R(j) ; " " ;
 +
          Next
 +
            Print
 +
      ')
 +
            Print "PING OK --> Exit Do..Loop"
 +
 +
            Set Ping_check_ok
 +
 +
          Exit Do                                          ' If we can an answer from NTP Server exit do ... loop
 +
 +
      Else
 +
        Print "NTP Server not available"
 +
      End If
 +
      Waitms 100
 +
 +
  Loop Until Ii = 3
 +
 +
  Ii = 0
 +
#else
 +
  Dim Ping_check_ok As Bit
 +
  Ping_check_ok = 1
 +
#endif
 +
 +
'-------------------------------------------------------------------------------
 +
'  SNTP
 +
'-------------------------------------------------------------------------------
 +
 +
If Ping_check_ok = 1 Then                                  'When the NTP Serverer responded to PING
 +
  'we need to get a socket first
 +
  'note that for UDP we specify sock_dgram
 +
  Idx = Getsocket(idx , Sock_dgram , 1000 , 0)                ' get socket for UDP mode, specify port
 +
  Print "Socket " ; Idx ; " " ; Idx
 +
 +
  Local_time = Sntp(idx , Ip_sntp_server)                    ' get time from SNTP server
 +
  Print "Local_time = " ; Local_time
 +
 +
  If Local_time < 100 Then                                    'try it again
 +
      Wait 1
 +
      Local_time = Sntp(idx , Ip_sntp_server)                  ' get time from SNTP server
 +
      Print "Second try ; Local_time = " ; Local_time
 +
  End If
 +
 +
  Local_time = Local_time + 3600                              ' (UTC/GMT) time + 3600
 +
  Print Date(local_time) ; Spc(3) ; Time(local_time)
 +
End If
 +
 +
'get a socket first
 +
'note that for UDP we specify sock_dgram
 +
Idx = Getsocket(idx , Sock_dgram , 1000 , 0)                ' get socket for UDP mode, specify port
 +
'Print "Socket " ; Idx ; " " ; Idx
 +
 +
 +
Do
 +
    If New_second = 1 Then
 +
      Reset New_second
 +
      'Do something every second ......
 +
    End If
 +
 +
      'The UDP header give us info about Peersize, Peerport and peeraddress
 +
      'which is the amount of data bytes received from peerport and peer ip address
 +
      Udpreadheader Idx                                    ' read the udp header (only the first 8 Bytes)
 +
 +
      If Peersize > 0 Then                                  ' the actual number of bytes (without header bytes)
 +
        Print "Size= " ; Peersize ; " By" ; "  Port= " ; Peerport ; " Sender IP= " ; Ip2str(peeraddress) ; "  Timestamp : " ; Date$ ; " / " ; Time$
 +
          Temp = Udpread(idx , S(1) , Peersize)            ' read the number of Bytes into Array S
 +
                Print "DATA = " ;
 +
          For Temp = 1 To Peersize
 +
              Print Chr(s(temp)) ;                          ' print what we have received over USART to debug interface
 +
          Next
 +
          Print
 +
        'Send it back to sender IP, Sender Port
 +
        Result = Udpwrite(peeraddress , Peerport , Idx , S(1) , Peersize)      ' write the received data back
 +
      End If
 +
Loop
 +
 +
End
 +
 +
Timer_irq:
 +
  Incr Local_time
 +
  Time$ = Time(local_time)
 +
  Date$ = Date(local_time)
 +
  Set New_second
 +
Return
 +
 +
Getdatetime:
 +
Return
 +
 +
Settime:
 +
Return
 +
 +
Setdate:
 +
Return
 +
</source>
  
  

Revision as of 14:30, 8 March 2013

Contents

Please read first this Article:

Getting started with Arduino and WIZ820io --> [1]


It uses the same source code exept we use here an Wiznet W5100 Chip intead of W5200 so only config TCPIP needs to be changed.

The usage of Easy TCP/IP in combination with that example is also the same.

Source Code:

The difference is only this part in the Bascom source code:


'Here you need MAC address, the ip address you like to use, subnet mask, gateway and localport
 Config Tcpip = Noint , _
 Mac = 1.1.94.127.1.255 , _
 Ip = 192.168.2.254 , _
 Submask = 255.255.255.0 , _
 Gateway = 192.168.2.1 , _
 Localport = 1000 , _
 Tx = $55 , Rx = $55 , _
 Chip = W5100 , _
 Spi = 1

Complete Source code:


' IP Address of Arduino = 192.168.2.254
' Port of Arduino = 1000
' We use UDP
'
 
'Use Hardware:
' - Arduino UNO R3
' - Arduino Ethernet Shield with W5100 Wiznet Chip
 
 
' NTP Server IP address (here you can change the NTP server of your choice)
Const Ntp1 = 192 : Const Ntp2 = 53 : Const Ntp3 = 103 : Const Ntp4 = 108       ' Example =  192.53.103.108
 
Const Use_ping = 1                                         'use PING NTP server for checking NTP server availability before move on
 
 
$regfile = "m328pdef.dat"
$crystal = 16000000                                         '16MHz
$hwstack = 100
$swstack = 100
$framesize = 400
 
Config Com1 = 57600 , Synchrone = 0 , Parity = None , Stopbits = 1 , Databits = 8 , Clockpol = 0
 
'-------------------------------------------------------------------------------
' Server Variables
'-------------------------------------------------------------------------------
Dim Ip_sntp_server As Long
'assign the IP number of a SNTP server
Ip_sntp_server = Maketcp(ntp1 , Ntp2 , Ntp3 , Ntp4)         'assign IP of NTP SERVER
 
 
 
Wait 2
Print
Print "-----START Arduino UNO R3 + Ethernet Shield DEMO-----"
'-------------------------------------------------------------------------------
' Network Hardware
'-------------------------------------------------------------------------------
Config Spi = Hard , Interrupt = Off , Data Order = Msb , Master = Yes , Polarity = Low , Phase = 0 , Clockrate = 4 , Noss = 0
Spiinit
 
Print
Enable Interrupts
 
  'Here you need MAC address, the ip address you like to use, subnet mask, gateway and localport
  Config Tcpip = Noint , _
            Mac = 1.1.94.127.1.255 , _
            Ip = 192.168.2.254 , _
            Submask = 255.255.255.0 , _
            Gateway = 192.168.2.1 , _
            Localport = 1000 , _
            Tx = $55 , Rx = $55 , _
            Chip = W5100 , _
            Spi = 1
 
 
'-------------------------------------------------------------------------------
'  Config Clock
'-------------------------------------------------------------------------------
Dim Local_time As Long
Dim New_second As Bit
 
Config Date = Dmy , Separator = .
Config Clock = User
 
Config Timer1 = Timer , Prescale = 256
On Timer1 Timer_irq Saveall                                 'the SAVEALL option is NEEDED !
Const Timer_preload = 3036
Enable Timer1
 
'-------------------------------------------------------------------------------
'  UDP
'-------------------------------------------------------------------------------
Dim Idx As Byte                                             ' socket number
Dim Result As Word                                          ' result
Dim S(255) As Byte
Dim R(255) As Byte
Dim Sstr As String * 255
Dim Temp As Byte , Temp2 As Byte                            ' temp bytes
Dim Ip As Long
 
'-------------------------------------------------------------------------------
'  PING NTP SERVER to check if NTP server is available
'-------------------------------------------------------------------------------
#if Use_ping = 1
   Dim J As Byte , Res As Byte
   Dim Ii As Byte
   Dim Ping_check_ok As Bit
 
   ' FILL PING ARRAY
   S(1) = 8                                                    'type is echo
   S(2) = 0                                                    'code
 
   S(3) = 0                                                    ' for checksum initialization
   S(4) = 0                                                    ' checksum
   S(5) = 0                                                    ' a signature can be any number
   S(6) = 1                                                    '   signature
   S(7) = 0                                                    ' sequence number - any number
   S(8) = 1
   S(9) = 65
 
   Dim W As Word At S + 2 Overlay                              'same as dta(3) and dta(4)
   Dim B As Byte
   W = Tcpchecksum(s(1) , 9)                                   ' calculate checksum and store in dta(3) and dta(4)
 
   'Ip = Maketcp(192.53.103.108)                                'try to check this google server
   Print "PING NTP Server : " ; Ip2str(ip_sntp_server)
 
   'Print "Socket " ; Idx ; " " ; Idx
   Setipprotocol Idx , 1                                       'set protocol to 1
   'the protocol value must be set BEFORE the socket is openend
 
   Idx = Getsocket(idx , Sock_ipl_raw , 5000 , 0)              'RAW Socket
 
   ' We try the PING 3 times (but if we get an answer we exit the for loop)
   Do
      Incr Ii
 
      Result = Udpwrite(ip_sntp_server , 7 , Idx , S(1) , 9)   'write ping data               '
      Print "Ping Number : " ; ii
      Waitms 200                                               ' depending on the hops, speed, etc
      Result = Socketstat(idx , Sel_recv)                      'check for data
    '  Print "REC:" ; Result
      If Result >= 11 Then
 
         Res = Tcpread(idx , R(1) , Result)                    'get data with TCPREAD !!!
 
      '     Print "DATA RETURNED :" ; Res
      '(                     '
           For J = 1 To Result
             Print R(j) ; " " ;
           Next
            Print
      ')
            Print "PING OK --> Exit Do..Loop"
 
            Set Ping_check_ok
 
           Exit Do                                          ' If we can an answer from NTP Server exit do ... loop
 
      Else
         Print "NTP Server not available"
      End If
      Waitms 100
 
   Loop Until Ii = 3
 
   Ii = 0
#else
  Dim Ping_check_ok As Bit
  Ping_check_ok = 1
#endif
 
'-------------------------------------------------------------------------------
'  SNTP
'-------------------------------------------------------------------------------
 
If Ping_check_ok = 1 Then                                   'When the NTP Serverer responded to PING
   'we need to get a socket first
   'note that for UDP we specify sock_dgram
   Idx = Getsocket(idx , Sock_dgram , 1000 , 0)                ' get socket for UDP mode, specify port
   Print "Socket " ; Idx ; " " ; Idx
 
   Local_time = Sntp(idx , Ip_sntp_server)                     ' get time from SNTP server
   Print "Local_time = " ; Local_time
 
   If Local_time < 100 Then                                    'try it again
      Wait 1
      Local_time = Sntp(idx , Ip_sntp_server)                  ' get time from SNTP server
      Print "Second try ; Local_time = " ; Local_time
   End If
 
   Local_time = Local_time + 3600                              ' (UTC/GMT) time + 3600
   Print Date(local_time) ; Spc(3) ; Time(local_time)
End If
 
'get a socket first
'note that for UDP we specify sock_dgram
Idx = Getsocket(idx , Sock_dgram , 1000 , 0)                ' get socket for UDP mode, specify port
'Print "Socket " ; Idx ; " " ; Idx
 
 
Do
    If New_second = 1 Then
      Reset New_second
      'Do something every second ......
    End If
 
      'The UDP header give us info about Peersize, Peerport and peeraddress
      'which is the amount of data bytes received from peerport and peer ip address
       Udpreadheader Idx                                    ' read the udp header (only the first 8 Bytes)
 
      If Peersize > 0 Then                                  ' the actual number of bytes (without header bytes)
         Print "Size= " ; Peersize ; " By" ; "  Port= " ; Peerport ; " Sender IP= " ; Ip2str(peeraddress) ; "  Timestamp : " ; Date$ ; " / " ; Time$
           Temp = Udpread(idx , S(1) , Peersize)            ' read the number of Bytes into Array S
                Print "DATA = " ;
           For Temp = 1 To Peersize
              Print Chr(s(temp)) ;                          ' print what we have received over USART to debug interface
           Next
           Print
         'Send it back to sender IP, Sender Port
         Result = Udpwrite(peeraddress , Peerport , Idx , S(1) , Peersize)       ' write the received data back
      End If
Loop
 
End
 
Timer_irq:
   Incr Local_time
   Time$ = Time(local_time)
   Date$ = Date(local_time)
   Set New_second
Return
 
Getdatetime:
Return
 
Settime:
Return
 
Setdate:
Return


Author

MAK3

Personal tools
Namespaces
Variants
Actions
Navigation
Language