1WREAD/de

Action

Dieser Befehl liest Daten vom 1wire bus in eine Variable.

 

 

Syntax

var2 = 1WREAD( [ bytes] )

var2 = 1WREAD( bytes , port , pin)

 

 

Beschreibung

var2	Liest ein Byte vom Bus und speichert es in die Variable var2.   Die Anzahl der zu lesenden Bytes kann optional angegeben werden.
Port	Der Name des PORT PINx Registers wie z.B. PINB oder PIND.
Pin	Die Pin-Nummer im Bereich von 0-7. Darf eine numerische Konstante oder Variable sein.

 

 

Mehrere 1-wire Busse an verschiedenen Pins werden unterstützt.

Dafür müssen die Optionen port und pin angegeben werden, die für die jeweilige Kommunikation benutzt werden.

 

Die 1wreset, 1wwrite und 1wread Befehle funktionieren bei Benutzung der alten Schreibweise. Der Pin kann über die Compiler-Optionen oder mit dem CONFIG 1WIRE statement eingestellt werden.

 

 

Die Syntax für zusätzliche 1-wire Busse lautet :

1WRESET port, pin

1WWRITE var/constant , bytes, port, pin

var = 1WREAD(bytes, port, pin) 'für das Lesen mehrere Bytes

 

 

Siehe auch

1WWRITE , 1WRESET

 

 

 

Beispiel

'--------------------------------------------------------------------------------
'name : 1wire.bas
'copyright : (c) 1995-2005, MCS Electronics
'purpose : demonstrates 1wreset, 1wwrite and 1wread()
'micro : Mega48
'suited for demo : yes
'commercial addon needed : no
' pull-up of 4K7 required to VCC from Portb.2
' DS2401 serial button connected to Portb.2
'--------------------------------------------------------------------------------
 
$regfile = "m48def.dat"
$crystal = 4000000
 
$hwstack = 32 'default use 32 for the hardware stack
$swstack = 10 'default use 10 for the SW stack
$framesize = 40 'default use 40 for the frame space
 
 
'when only bytes are used, use the following lib for smaller code
$lib "mcsbyte.lib"
 
 
Config 1wire = Portb.0 'use this pin
'On the STK200 jumper B.0 must be inserted
Dim Ar(8) As Byte , A As Byte , I As Byte
 
 
Do
Wait 1
1wreset 'reset the device
Print Err 'print error 1 if error
1wwrite &H33 'read ROM command
For I = 1 To 8
 Ar(i) = 1wread() 'place into array
Next
 
 
'You could also read 8 bytes a time by unremarking the next line
'and by deleting the for next above
'Ar(1) = 1wread(8) 'read 8 bytes
 
 
For I = 1 To 8
 Print Hex(ar(i)); 'print output
Next
Print 'linefeed
Loop
 
 
'NOTE THAT WHEN YOU COMPILE THIS SAMPLE THE CODE WILL RUN TO THIS POINT
'THIS because of the DO LOOP that is never terminated!!!
 
 
'New is the possibility to use more than one 1 wire bus
'The following syntax must be used:
For I = 1 To 8
Ar(i) = 0 'clear array to see that it works
Next
 
 
1wreset Pinb , 2 'use this port and pin for the second device
1wwrite &H33 , 1 , Pinb , 2 'note that now the number of bytes must be specified!
'1wwrite Ar(1) , 5,pinb,2
 
 
'reading is also different
Ar(1) = 1wread(8 , Pinb , 2) 'read 8 bytes from portB on pin 2
 
 
For I = 1 To 8
Print Hex(ar(i));
Next
 
 
'you could create a loop with a variable for the bit number !
For I = 0 To 3 'for pin 0-3
1wreset Pinb , I
1wwrite &H33 , 1 , Pinb , I
Ar(1) = 1wread(8 , Pinb , I)
For A = 1 To 8
 Print Hex(ar(a));
Next
Print
Next
End

Languages	English • Deutsch