Admin: 1 revision

2013-02-15T19:16:37Z

1 revision

Admin: Created page with "= Action = Sends a house and key code with the X10 protocol.
2013-02-12T19:20:11Z

Created page with "= Action = Sends a house and key code with the X10 protocol. Action =

Sends a house and key code with the X10 protocol.

 

 

= Syntax =

X10SEND house , code

 

 

= Remarks =
<div style="padding: 0px; margin: 0px 0px 0px 4px;">
{| width="609" cellspacing="0" cellpadding="1" border="1" style="border: 2px solid rgb(0, 0, 0); border-spacing: 0px; border-collapse: collapse;"
|- style="vertical-align: top;"
| valign="top" width="15%" style="width: 88px; border: 1px solid rgb(0, 0, 0);" |
House

| valign="top" width="100%" style="width: 512px; border: 1px solid rgb(0, 0, 0);" |
The house code in the form of a letter A-P.

 

You can use a constant, or you can use a variable

|- style="vertical-align: top;"
| valign="top" width="15%" style="width: 88px; border: 1px solid rgb(0, 0, 0);" |
Code

| valign="top" width="100%" style="width: 512px; border: 1px solid rgb(0, 0, 0);" |
The code or function to send. This is a number between 1-32.

|}
</div>
 

The X10SEND command needs a TW-523 interface.

Only ground, TX and Zero Cross, needs to be connected for transmission.

Use CONFIG X10 to specify the pins.

 

X10 is a popular protocol used to control equipment via the mains. A 110 KHz signal is added to the normal 50/60 Hz , 220/110 V power.

 

Notice that experimenting with 110V-240V can be very dangerous when you do not know exactly what you are doing !!!

 

In the US, X10 is very popular and wide spread. In Europe it is hard to get a TW-523 for 220/230/240 V.

 

I modified an 110V version so it worked for 220V. On the Internet you can find modification information. But as noticed before, MODIFY ONLY WHEN YOU UNDERSTAND WHAT YOU ARE DOING.

 

A bad modified device could result in a fire, and your insurance will most likely not pay. A modified device will not pass any CE, or other test.

 

When the TW-523 is connected to the mains and you use the X10SEND command, you will notice that the LED on the TW-523 will blink.

 

 

The following table lists all X10 codes.
<div style="padding: 0px; margin: 0px 0px 0px 4px;">
{| width="634" cellspacing="0" cellpadding="1" border="1" style="border: 2px solid rgb(0, 0, 0); border-spacing: 0px; border-collapse: collapse;"
|- style="vertical-align: top;"
| valign="top" width="22%" bgcolor="#ffff99" style="width: 136px; background-color: rgb(255, 255, 153); border: 1px solid rgb(0, 0, 0);" |
Code value

| valign="top" width="100%" bgcolor="#ffff99" style="width: 489px; background-color: rgb(255, 255, 153); border: 1px solid rgb(0, 0, 0);" |
Description

|- style="vertical-align: top;"
| valign="top" width="22%" style="width: 136px; border: 1px solid rgb(0, 0, 0);" |
1-16

| valign="top" width="100%" style="width: 489px; border: 1px solid rgb(0, 0, 0);" |
Used to address a unit. X10 can use a maximum of 16 units per house code.

|- style="vertical-align: top;"
| valign="top" width="22%" style="width: 136px; border: 1px solid rgb(0, 0, 0);" |
17

| valign="top" width="100%" style="width: 489px; border: 1px solid rgb(0, 0, 0);" |
All units off

|- style="vertical-align: top;"
| valign="top" width="22%" style="width: 136px; border: 1px solid rgb(0, 0, 0);" |
18

| valign="top" width="100%" style="width: 489px; border: 1px solid rgb(0, 0, 0);" |
All lights on

|- style="vertical-align: top;"
| valign="top" width="22%" style="width: 136px; border: 1px solid rgb(0, 0, 0);" |
19

| valign="top" width="100%" style="width: 489px; border: 1px solid rgb(0, 0, 0);" |
ON

|- style="vertical-align: top;"
| valign="top" width="22%" style="width: 136px; border: 1px solid rgb(0, 0, 0);" |
20

| valign="top" width="100%" style="width: 489px; border: 1px solid rgb(0, 0, 0);" |
OFF

|- style="vertical-align: top;"
| valign="top" width="22%" style="width: 136px; border: 1px solid rgb(0, 0, 0);" |
21

| valign="top" width="100%" style="width: 489px; border: 1px solid rgb(0, 0, 0);" |
DIM

|- style="vertical-align: top;"
| valign="top" width="22%" style="width: 136px; border: 1px solid rgb(0, 0, 0);" |
22

| valign="top" width="100%" style="width: 489px; border: 1px solid rgb(0, 0, 0);" |
BRIGHT

|- style="vertical-align: top;"
| valign="top" width="22%" style="width: 136px; border: 1px solid rgb(0, 0, 0);" |
23

| valign="top" width="100%" style="width: 489px; border: 1px solid rgb(0, 0, 0);" |
All lights off

|- style="vertical-align: top;"
| valign="top" width="22%" style="width: 136px; border: 1px solid rgb(0, 0, 0);" |
24

| valign="top" width="100%" style="width: 489px; border: 1px solid rgb(0, 0, 0);" |
Extended ode

|- style="vertical-align: top;"
| valign="top" width="22%" style="width: 136px; border: 1px solid rgb(0, 0, 0);" |
25

| valign="top" width="100%" style="width: 489px; border: 1px solid rgb(0, 0, 0);" |
Hail request

|- style="vertical-align: top;"
| valign="top" width="22%" style="width: 136px; border: 1px solid rgb(0, 0, 0);" |
26

| valign="top" width="100%" style="width: 489px; border: 1px solid rgb(0, 0, 0);" |
Hail acknowledge

|- style="vertical-align: top;"
| valign="top" width="22%" style="width: 136px; border: 1px solid rgb(0, 0, 0);" |
27

| valign="top" width="100%" style="width: 489px; border: 1px solid rgb(0, 0, 0);" |
Preset dim

|- style="vertical-align: top;"
| valign="top" width="22%" style="width: 136px; border: 1px solid rgb(0, 0, 0);" |
28

| valign="top" width="100%" style="width: 489px; border: 1px solid rgb(0, 0, 0);" |
Preset dim

|- style="vertical-align: top;"
| valign="top" width="22%" style="width: 136px; border: 1px solid rgb(0, 0, 0);" |
29

| valign="top" width="100%" style="width: 489px; border: 1px solid rgb(0, 0, 0);" |
Extended data analog

|- style="vertical-align: top;"
| valign="top" width="22%" style="width: 136px; border: 1px solid rgb(0, 0, 0);" |
30

| valign="top" width="100%" style="width: 489px; border: 1px solid rgb(0, 0, 0);" |
Status on

|- style="vertical-align: top;"
| valign="top" width="22%" style="width: 136px; border: 1px solid rgb(0, 0, 0);" |
31

| valign="top" width="100%" style="width: 489px; border: 1px solid rgb(0, 0, 0);" |
Status off

|- style="vertical-align: top;"
| valign="top" width="22%" style="width: 136px; border: 1px solid rgb(0, 0, 0);" |
32

| valign="top" width="100%" style="width: 489px; border: 1px solid rgb(0, 0, 0);" |
Status request

|}
</div>
 

 

At www.x10.com you can find all X10 information. The intension of BASCOM is not to learn you everything about X10, but to show you how you can use it with BASCOM.

 

 

= See also =

[[CONFIG X10|CONFIG X10]] , [[X10DETECT]] 

 

 

= Example =

See [[X10DETECT]]

 {{Languages}}

[[Category:BASCOM Language Reference/de]]