Admin: 1 revision

2013-02-15T19:15:54Z

1 revision

Admin: Created page with "= Action = Writes to an ethernet chip register ..."

2013-02-12T16:23:14Z

Created page with "= Action = Writes to an ethernet chip register ..."

New page

== (**COPIED FROM ENGLISH PAGE**) === Action =

Writes to an ethernet chip register

 

 

= Syntax =

SETTCPREGS address, var , bytes

 

 

= Remarks =
<div style="padding: 0px; margin: 0px 0px 0px 4px;">
{| width="604" cellspacing="0" cellpadding="1" border="1" style="border: 2px solid rgb(0, 0, 0); border-spacing: 0px; border-collapse: collapse;"
|- style="vertical-align: top;"
| valign="top" width="15%" style="width: 87px; border: 1px solid rgb(0, 0, 0);" |
address

| valign="top" width="100%" style="width: 508px; border: 1px solid rgb(0, 0, 0);" |
The address of the register. This must be the address of the MSB, or the address with the lowest address. The address should not include the base address.

|- style="vertical-align: top;"
| valign="top" width="15%" style="width: 87px; border: 1px solid rgb(0, 0, 0);" |
var

| valign="top" width="100%" style="width: 508px; border: 1px solid rgb(0, 0, 0);" |
The variable to write.

|- style="vertical-align: top;"
| valign="top" width="15%" style="width: 87px; border: 1px solid rgb(0, 0, 0);" |
bytes

| valign="top" width="100%" style="width: 508px; border: 1px solid rgb(0, 0, 0);" |
The number of bytes to write.

|}
</div>
 

Most options are implemented with BASCOM statements or functions. When there is a need to write to the ethernet chip register you can use the SETTCPREGS commands. It can write multiple bytes. It is important that you specify the lowest address. The settcpregs statement will add the base address of the chip to the address so you should not add it yourself. Use the address from the datasheet.

The addresses are different for the W3100,W5100,W5200 and W5300.

 

 

= See also =

[[GETTCPREGS]]

 

 

= ASM =

NONE

 

 

= Example =

 <source lang="bascomavr">
'-----------------------------------------------------------------------------------------
'name : regs_SPI.bas
'copyright : (c) 1995-2012, MCS Electronics
'purpose : test custom regs reading writing
'micro : Mega88
'suited for demo : yes
'commercial addon needed : no
'-----------------------------------------------------------------------------------------
$regfile = "m88def.dat" ' specify the used micro

$crystal = 8000000 ' used crystal frequency
$baud = 19200 ' use baud rate
$hwstack = 80 ' default use 32 for the hardware stack
$swstack = 128 ' default use 10 for the SW stack
$framesize = 80 ' default use 40 for the frame space

Dim L As Long

Config Spi = Hard , Interrupt = Off , Data Order = Msb , Master = Yes , Polarity = Low , Phase = 0 , Clockrate = 4 , Noss = 0
'Init the spi pins
Spiinit

'we do the usual
Print "Init TCP" ' display a message
Enable Interrupts ' before we use config tcpip , we need to enable the interrupts
Config Tcpip = Int1 , Mac = 12.128.12.34.56.78 , Ip = 192.168.1.70 , Submask = 255.255.255.0 , Gateway = 192.168.1.1 , Localport = 1000 , Tx = $55 , Rx = $55 , Chip = W5100 , Spi = 1
Print "Init done"

'set the IP address to 192.168.0.135
Settcp 12.128.12.24.56.78 , 192.168.1.135 , 255.255.255.0 , 192.168.1.1

'now read the IP address direct from the registers
L = Gettcpregs(&H0f , 4)
Print Ip2str(l)

Dim B4 As Byte At L Overlay ' this byte is the same as the LSB of L

'now make the IP address 192.168.1.136 by writing to the LSB
B4 = 136
Settcpregs &H0F , L , 4 'write

'and check if it worked
L = Gettcpregs(&H0f , 4)
Print Ip2str(l)

'and with PING you can check again that now it works

End
</source> {{Languages}}

[[Category:BASCOM Language Reference/de]]

SETTCPREGS/de - Revision history

Admin: 1 revision

Admin: Created page with "= Action = Writes to an ethernet chip register ..."