Admin: 1 revision

2013-02-15T19:13:54Z

1 revision

Admin: Created page with "= Action = Configures the pins used for X10. ..."

2013-02-08T12:05:18Z

Created page with "= Action = Configures the pins used for X10. ..."

Neue Seite

== (**COPIED FROM ENGLISH PAGE**) === Action =

Configures the pins used for X10.

 

 

= Syntax =

CONFIG X10 = pinZC , TX = portpin

 

 

= Remarks =
<div style="padding: 0px; margin: 0px 0px 0px 4px;">
{| width="609" cellspacing="0" cellpadding="1" border="1" style="border: 2px solid rgb(0, 0, 0); border-spacing: 0px; border-collapse: collapse;"
|- style="vertical-align: top;"
| valign="top" width="14%" style="width: 81px; border: 1px solid rgb(0, 0, 0);" |
PinZC

| valign="top" width="100%" style="width: 519px; border: 1px solid rgb(0, 0, 0);" |
The pin that is connected to the zero cross output of the TW-523. This is a pin that will be used as INPUT.

|- style="vertical-align: top;"
| valign="top" width="14%" style="width: 81px; border: 1px solid rgb(0, 0, 0);" |
Portpin

| valign="top" width="100%" style="width: 519px; border: 1px solid rgb(0, 0, 0);" |
The pin that is connected to the TX pin of the TW-523.

 

TX is used to send X10 data to the TW-523. This pin will be used in output mode.

|}
</div>
 

 

The TW-523 RJ-11 connector has the following pinout:
<div style="padding: 0px; margin: 0px 0px 0px 4px;">
{| width="464" cellspacing="0" cellpadding="1" border="1" style="border: 2px solid rgb(0, 0, 0); border-spacing: 0px; border-collapse: collapse;"
|- style="vertical-align: top;"
| valign="top" width="32%" bgcolor="#ffff99" style="width: 145px; background-color: rgb(255, 255, 153); border: 1px solid rgb(0, 0, 0);" |
Pin

| valign="top" width="38%" bgcolor="#ffff99" style="width: 172px; background-color: rgb(255, 255, 153); border: 1px solid rgb(0, 0, 0);" |
Description

| valign="top" width="100%" bgcolor="#ffff99" style="width: 135px; background-color: rgb(255, 255, 153); border: 1px solid rgb(0, 0, 0);" |
Connect to micro

|- style="vertical-align: top;"
| valign="top" width="32%" style="width: 145px; border: 1px solid rgb(0, 0, 0);" |
1

| valign="top" width="38%" style="width: 172px; border: 1px solid rgb(0, 0, 0);" |
Zero Cross

| valign="top" width="100%" style="width: 135px; border: 1px solid rgb(0, 0, 0);" |
Input pin. Add 5.1K pull up.

|- style="vertical-align: top;"
| valign="top" width="32%" style="width: 145px; border: 1px solid rgb(0, 0, 0);" |
2

| valign="top" width="38%" style="width: 172px; border: 1px solid rgb(0, 0, 0);" |
GND

| valign="top" width="100%" style="width: 135px; border: 1px solid rgb(0, 0, 0);" |
GND

|- style="vertical-align: top;"
| valign="top" width="32%" style="width: 145px; border: 1px solid rgb(0, 0, 0);" |
3

| valign="top" width="38%" style="width: 172px; border: 1px solid rgb(0, 0, 0);" |
RX

| valign="top" width="100%" style="width: 135px; border: 1px solid rgb(0, 0, 0);" |
Not used.

|- style="vertical-align: top;"
| valign="top" width="32%" style="width: 145px; border: 1px solid rgb(0, 0, 0);" |
4

| valign="top" width="38%" style="width: 172px; border: 1px solid rgb(0, 0, 0);" |
TX

| valign="top" width="100%" style="width: 135px; border: 1px solid rgb(0, 0, 0);" |
Output pin. Add 1K pull up.

|}
</div>
 

 

= See also =

[[X10DETECT]] , [[X10SEND]]

 

 

= Example =

 <source lang="bascomavr">
'-----------------------------------------------------------------------------------------
'name : x10.bas
'copyright : (c) 1995-2005, MCS Electronics
'purpose : example needs a TW-523 X10 interface
'micro : Mega48
'suited for demo : yes
'commercial addon needed : no
'-----------------------------------------------------------------------------------------

$regfile = "m48def.dat" ' specify the used micro
$crystal = 8000000 ' used crystal frequency
$baud = 19200 ' use baud rate
$hwstack = 32 ' default use 32 for the hardware stack
$swstack = 10 ' default use 10 for the SW stack
$framesize = 40 ' default use 40 for the frame space

'define the house code
Const House = "M" ' use code A-P

Waitms 500 ' optional delay not really needed

'dim the used variables
Dim X As Byte

'configure the zero cross pin and TX pin
Config X10 = Pind.4 , Tx = Portb.0
' ^--zero cross
' ^--- transmission pin

'detect the TW-523
X = X10detect()
Print X ' 0 means error, 1 means 50 Hz, 2 means 60 Hz

Do
Input "Send (1-32) " , X
'enter a key code from 1-31
'1-16 to address a unit
'17 all units off
'18 all lights on
'19 ON
'20 OFF
'21 DIM
'22 BRIGHT
'23 All lights off
'24 extended code
'25 hail request
'26 hail acknowledge
'27 preset dim
'28 preset dim
'29 extended data analog
'30 status on
'31 status off
'32 status request

X10send House , X ' send the code
Loop

Dim Ar(4) As Byte
X10send House , X , Ar(1) , 4 ' send 4 additional bytes
End
</source> {{Languages}}

[[Category:BASCOM Language Reference/de]]

CONFIG X10/de - Revision history

Admin: 1 revision

Admin: Created page with "= Action = Configures the pins used for X10. ..."