CONFIG TIMER1 - Revision history

Admin: Created page with "= Action = Configure TIMER1. =
2013-02-08T11:37:40Z

Created page with "= <span class="f_Header">Action</span> = Configure TIMER1. <span style="font-family: Arial;"> </span> <span style="font-family: Arial;"> </span> = <span class="f..."

Neue Seite
= <span class="f_Header">Action</span> =

Configure TIMER1.

<span style="font-family: Arial;"> </span>

<span style="font-family: Arial;"> </span>

= <span class="f_Header">Syntax</span> =

<span class="f_Syntax">CONFIG TIMER1</span> = COUNTER | TIMER | PWM ,

EDGE=RISING | FALLING , PRESCALE= 1|8|64|256|1024 ,

NOISE_CANCEL=0 |1, CAPTURE_EDGE = RISING | FALLING ,

CLEAR_TIMER = 1|0,

COMPARE_A = CLEAR | SET | TOGGLE | DISCONNECT ,

COMPARE_B = CLEAR | SET | TOGGLE | DISCONNECT ,

PWM = 8 | 9 10 ,

COMPARE_A_PWM = CLEAR_UP| CLEAR_DOWN | DISCONNECT

COMPARE_B_PWM = CLEAR_UP| CLEAR_DOWN | DISCONNECT

[,CONFIGURATION=NAME]

<span style="font-family: Arial;"> </span>

<span style="font-family: Arial;"> </span>

= <span class="f_Header">Remarks</span> =

The TIMER1 is a 16 bit counter. See the hardware description of TIMER1.

It depends on the chip if COMPARE_B is available or not.

Some chips even have a COMARE_C.

<span style="font-family: Arial;"> </span>

The syntax shown above must be on one line. Not all the options need to be selected.

<span style="font-family: Arial;"> </span>

<span style="font-family: Arial;"> </span>

Here is the effect of the various options.
<div style="padding: 0px; margin: 0px 0px 0px 4px;">
{| width="604" cellspacing="0" cellpadding="1" border="1" style="border: 2px solid rgb(0, 0, 0); border-spacing: 0px; border-collapse: collapse;"
|- style="vertical-align: top;"
| valign="top" width="19%" style="width: 111px; border: 1px solid rgb(0, 0, 0);" |
EDGE

| valign="top" width="100%" style="width: 484px; border: 1px solid rgb(0, 0, 0);" |
You can select whether the TIMER will count on the falling or rising edge. Only for COUNTER mode.

|- style="vertical-align: top;"
| valign="top" width="19%" style="width: 111px; border: 1px solid rgb(0, 0, 0);" |
CAPTURE_ EDGE

| valign="top" width="100%" style="width: 484px; border: 1px solid rgb(0, 0, 0);" |
You can choose to capture the TIMER registers to the INPUT CAPTURE registers

<span style="font-family: Arial;"> </span>

With the CAPTURE_EDGE = FALLING/RISING, you can specify to capture on the falling or rising edge of pin ICP

|- style="vertical-align: top;"
| valign="top" width="19%" style="width: 111px; border: 1px solid rgb(0, 0, 0);" |
NOISE_ CANCELING

| valign="top" width="100%" style="width: 484px; border: 1px solid rgb(0, 0, 0);" |
To allow noise canceling you can provide a value of 1.

|- style="vertical-align: top;"
| valign="top" width="19%" style="width: 111px; border: 1px solid rgb(0, 0, 0);" |
PRESCALE

| valign="top" width="100%" style="width: 484px; border: 1px solid rgb(0, 0, 0);" |
The TIMER is connected to the system clock in this case. You can select the division of the system clock with this parameter.

<span style="font-family: Arial;"> </span>

Valid values are 1 , 8, 64, 256 or 1024

PRESCALE can't be used in COUNTER mode.

|}
</div>
<span style="font-family: Arial;"> </span>

<span style="font-family: Arial;"> </span>

<span style="font-family: Arial;"> </span>

The TIMER1 also has two compare registers A and B

<span style="font-family: Arial;"> </span>

When the timer value matches a compare register, an action can be performed
<div style="padding: 0px; margin: 0px 0px 0px 4px;">
{| width="604" cellspacing="0" cellpadding="1" border="1" style="border: 2px solid rgb(0, 0, 0); border-spacing: 0px; border-collapse: collapse;"
|- style="vertical-align: top;"
| valign="top" width="16%" style="width: 93px; border: 1px solid rgb(0, 0, 0);" |
COMPARE_A

| valign="top" width="100%" style="width: 502px; border: 1px solid rgb(0, 0, 0);" |
The action can be:

<span style="font-family: Arial;"> </span>

SET will set the OC1X pin

CLEAR will clear the OC1X pin

TOGGLE will toggle the OC1X pin

DISCONNECT will disconnect the TIMER from output pin OC1X

|}
</div>
<span style="font-family: Arial;"> </span>

And the TIMER can be used in PWM mode.

You have the choice between 8, 9 or 10 bit PWM mode

<span style="font-family: Arial;"> </span>

Also you can specify if the counter must count UP or down after a match to the compare registers

Note that there are two compare registers A and B

<span style="font-family: Arial;"> </span>
<div style="padding: 0px; margin: 0px 0px 0px 4px;">
{| width="604" cellspacing="0" cellpadding="1" border="1" style="border: 2px solid rgb(0, 0, 0); border-spacing: 0px; border-collapse: collapse;"
|- style="vertical-align: top;"
| valign="top" width="26%" style="width: 153px; border: 1px solid rgb(0, 0, 0);" |
PWM

| valign="top" width="100%" style="width: 442px; border: 1px solid rgb(0, 0, 0);" |
Can be 8, 9 or 10.

|- style="vertical-align: top;"
| valign="top" width="26%" style="width: 153px; border: 1px solid rgb(0, 0, 0);" |
COMPARE_A_PWM

| valign="top" width="100%" style="width: 442px; border: 1px solid rgb(0, 0, 0);" |
PWM compare mode. Can be CLEAR_UP or CLEAR_DOWN

|}
</div>
<span style="font-family: Arial;"> </span>

<span style="font-family: Arial;"> </span>

Using COMPARE_A, COMPARE_B, COMPARE_A_PWM or COMPARE_B_PWM will set the corresponding pin for output. When this is not desired you can use the alternative NO_OUTPUT version that will not alter the output pin.

<span style="font-family: Arial;"> </span>

For example : COMPARE_A_NO_OUTPUT , COMPARE_A_PWM NO_OUTPUT

 

CONFIGURATION is optional. When you add configuration=mysetting, you can use this setting when you start the timer : START TIMER0 , mysetting

If you have multiple settings, you can start the timer with these different settings.

 

<span style="font-family: Arial;"> </span>

= <span class="f_Header">Example</span> =

<br/><source lang="bascomavr">
'-----------------------------------------------------------------------------------------
'name : timer1.bas
'copyright : (c) 1995-2005, MCS Electronics
'purpose : show using Timer1
'micro : 90S8515
'suited for demo : yes
'commercial addon needed : no
'-----------------------------------------------------------------------------------------

$regfile = "8515def.dat" ' specify the used micro
$crystal = 4000000 ' used crystal frequency
$baud = 19200 ' use baud rate
$hwstack = 32 ' default use 32 for the hardware stack
$swstack = 10 ' default use 10 for the SW stack
$framesize = 40 ' default use 40 for the frame space

Dim W As Word

'The TIMER1 is a versatile 16 bit TIMER.
'This example shows how to configure the TIMER

'First like TIMER0 , it can be set to act as a TIMER or COUNTER
'Lets configure it as a TIMER that means that it will count and that
'the input is provided by the internal clock.
'The internal clock can be divided by 1,8,64,256 or 1024
Config Timer1 = Timer , Prescale = 1024

'You can read or write to the timer with the COUNTER1 or TIMER1 variable
W = Timer1
Timer1 = W

'To use it as a COUNTER, you can choose on which edge it is trigereed
Config Timer1 = Counter , Edge = Falling
'Config Timer1 = Counter , Edge = Rising

'Also you can choose to capture the TIMER registers to the INPUT CAPTURE registers
'With the CAPTURE EDGE = , you can specify to capture on the falling or rising edge of
'pin ICP
Config Timer1 = Counter , Edge = Falling , Capture_Edge = Falling
'Config Timer1 = Counter , Edge = Falling , Capture Edge = Rising

'To allow noise canceling you can also provide :
Config Timer1 = Counter , Edge = Falling , Capture_Edge = Falling , Noise_Cancel = 1

'to read the input capture register :
W = Capture1
'to write to the capture register :
Capture1 = W

'The TIMER also has two compare registers A and B
'When the timer value matches a compare register, an action can be performed
Config Timer1 = Counter , Edge = Falling , Compare_A = Set , Compare_B = Toggle , Clear_Timer = 1
'SET , will set the OC1X pin
'CLEAR, will clear the OC1X pin
'TOGGLE, will toggle the OC1X pin
'DISCONNECT, will disconnect the TIMER from output pin OC1X
'CLEAR TIMER will clear the timer on a compare A match

'To read write the compare registers, you can use the COMPARE1A and COMPARE1B variables
Compare1a = W
W = Compare1a

'And the TIMER can be used in PWM mode
'You have the choice between 8,9 or 10 bit PWM mode
'Also you can specify if the counter must count UP or down after a match
'to the compare registers
'Note that there are two compare registers A and B
Config Timer1 = Pwm , Pwm = 8 , Compare_A_Pwm = Clear_Up , Compare_B_Pwm = Clear_Down , Prescale = 1

'to set the PWM registers, just assign a value to the compare A and B registers
Compare1a = 100
Compare1b = 200

'Or for better reading :
Pwm1a = 100
Pwm1b = 200
End
</source><br/>{{Languages}}

[[Category:BASCOM Language Reference]]