Admin: 1 revision

2013-02-15T19:13:01Z

1 revision

Admin: Created page with "= Action = Puts the Message Object into Transmit mode and send out data.
2013-02-07T16:34:47Z

Created page with "= Action = Puts the Message Object into Transmit mode and send out data. Action =

Puts the Message Object into Transmit mode and send out data.

 

 

= Syntax =

status = CANSEND(object, var[,bytes])

 

 

= Remarks =
<div style="padding: 0px; margin: 0px 0px 0px 4px;">
{| width="539" cellspacing="0" cellpadding="1" border="1" style="border: 2px solid rgb(0, 0, 0); border-spacing: 0px; border-collapse: collapse;"
|- style="vertical-align: top;"
| valign="top" width="15%" style="width: 77px; border: 1px solid rgb(0, 0, 0);" |
status

| valign="top" style="border: 1px solid rgb(0, 0, 0);" |
The status of sending the frame. This should be 0 if there was no problem. If there is an error it will return 1 or higher. The return value is the CANSTMOB register content with the TX bit cleared.

|- style="vertical-align: top;"
| valign="top" width="15%" style="width: 77px; border: 1px solid rgb(0, 0, 0);" |
object

| valign="top" style="border: 1px solid rgb(0, 0, 0);" |
The message object number in the range from 0-14.

The MOB must have been configured into the DISABLED mode before CANSEND can be used.

|- style="vertical-align: top;"
| valign="top" width="15%" style="width: 77px; border: 1px solid rgb(0, 0, 0);" |
var

| valign="top" style="border: 1px solid rgb(0, 0, 0);" |
A variable or array which content will be send. The data type of the variable will be used to determine the number of bytes to send.

|- style="vertical-align: top;"
| valign="top" width="15%" style="width: 77px; border: 1px solid rgb(0, 0, 0);" |
bytes

| valign="top" style="border: 1px solid rgb(0, 0, 0);" |
This is an optional value. You can specify how many bytes must be transmitted.

|}
</div>
 

The CANSEND function will disable the TX interrupt and then polls the CANSTMOB register for a change of flags. The TX flag is cleared so that a successful transmission returns a 0.

In case of ACK errors or other errors, a value other then 0 will be returned. Right after the status has changed, the TX and Error interrupt are enabled again and the CAN interrupt routine is executed. You need to reconfigure the MOB in all cases otherwise you can not send new data.

 

 

 

= See also =

[[CONFIG CANBUS|CONFIG CANBUS]] , [[CONFIG CANMOB|CONFIG CANMOB]] , [[CANBAUD]] , [[CANRESET]] , [[CANCLEARMOB]] , [[CANCLEARALLMOBS]] , [[CANRECEIVE]] , [[CANID]] , [[CANSELPAGE]] , [[CANGETINTS]]

 

 

 

 

= Example =

Have a look at [[CONFIG CANBUS|CONFIG CANBUS]] for a full example.

The code below only demonstrates that you MUST configure the MOB again in the interrupt routine.

The code below is taken from the sample you find under CONFIG CANBUS

 <source lang="bascomavr">
Elseif Canstmob.6 = 1 Then 'transmission ready
Config Canmob = -1 , Bitlen = 11 , Msgobject = Disabled , Msglen = 1 , Clearmob = No
' reconfig with value -1 for the current MOB and do not set ID and MASK
Elseif Canstmob.0 = 1 Then 'ACK ERROR
Config Canmob = -1 , Bitlen = 11 , Msgobject = Disabled , Msglen = 1 , Clearmob = No
' reconfig with value -1 for the current MOB and do not set ID and MASK
</source> {{Languages}}

[[Category:BASCOM Language Reference/de]]