View source

== (**COPIED FROM ENGLISH PAGE**) ==The USB Add On is a commercial add on which is available from the MCS Electronics Web Shop.

The CONFIG USB statement needs this add on. The add on is written in BASCOM BASIC mixed with assembler. Since the examples from Atmel were not really consistent, it took some effort to create reusable code. At a later stage, a number of routines will be moved to an assembler library.

The advantage of the BASCOM code is that it is similar to the C-code examples.

&nbsp;

[[File:Notice.jpg|notice]]Please read this entire topic first before you start with experiments.

&nbsp;

The Add On only supports the device mode. There is no support for host mode yet. In fact the add on is just the first step into USB support.

&nbsp;

To use the USB Add on, unzip all the files to the SAMPLES\USB directory.

You will find three samples&nbsp;:
<div style="padding: 0px; margin: 0px;">
{| border="0" cellpadding="0" cellspacing="0"
|- valign="baseline" style="vertical-align: baseline;"
| width="13" | <span style="font-size: 10pt; font-family: 'Arial Unicode MS', 'Lucida Sans Unicode', Arial;">•</span>
| hid_generic-162.bas
|}
</div><div style="padding: 0px; margin: 0px;">
{| border="0" cellpadding="0" cellspacing="0"
|- valign="baseline" style="vertical-align: baseline;"
| width="13" | <span style="font-size: 10pt; font-family: 'Arial Unicode MS', 'Lucida Sans Unicode', Arial;">•</span>
| virtcom-162.bas
|}
</div><div style="padding: 0px; margin: 0px;">
{| border="0" cellpadding="0" cellspacing="0"
|- valign="baseline" style="vertical-align: baseline;"
| width="13" | <span style="font-size: 10pt; font-family: 'Arial Unicode MS', 'Lucida Sans Unicode', Arial;">•</span>
| hid_keyboard-162.bas
|}
</div>
&nbsp;

The same samples are also provided for the USB1287.

&nbsp;

And you will find the include file&nbsp;:&nbsp;<span style="font-weight: bold;">usbinc.bas</span>. It is not allowed to distribute any of the files.

<span class="f_ImageCaption">&nbsp;</span>

Further, you will find a subdirectory named VB which contains a simple VB generic HID sample that uses the HIDX.OCX from the OCX subdirectory.

&nbsp;

The PDF directory contains a PDF with a translation between PS2 scan codes and USB key codes.

&nbsp;

The TOOLS directory contains the USBDEVIEW.EXE which can be used to display all USB devices,

&nbsp;

The CDC-Driver directory contains the INF file you need for the CDC/Virtual COM port example.

&nbsp;

The USB162 has a boot loader which can be programmed by USB using FLIP. BASCOM will also support this USB boot loader in version 1.11.9.2.

It is great for development but of course the boot loader uses some space which you probably need. The chip is also programmable via the normal way with the ISP protocol. when you do not use FLIP, and you erase the chip, the boot loader from Atmel is erased too! You can always reprogram the Atmel boot loader. But not using FLIP which depends on the boot loader.

&nbsp;

For USB to work properly the chip needs a good oscillator. The internal oscillator is not good enough. For that reason, the USB162 module from MCS has a 8 MHz crystal. Your hardware should use a crystal or crystal oscillator too.

&nbsp;

It is not the intention of MCS or the documentation to learn you everything about USB. There is a lot of information available from various sources. It is the goal of MCS to make it easy to use USB with your AVR micro. When there is enough demand for it, a special Wizard will be created to be able to generate HID applications.

&nbsp;

= <span class="f_Header">HID Keyboard</span> =

Let's begin with a simple program. Load the hid_keyboard-162.bas sample and compile it. Use either FLIP or a different programmer to program the chip. Each program has some important settings.

&nbsp;

Const Mdbg = 1 &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;' add print to see what is happening

Const Chiddevice = 1 &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; ' this is a HID device

&nbsp;

<span style="font-weight: bold;">MDBG</span>&nbsp;is a constant that can be set to 0 since all the print statements will use flash code. When you are new to USB and want to look at the events, it is good to have it turned on. You can view all events from the program.

<span style="font-weight: bold;">cHIDdevice</span>&nbsp;need to be set to 1 when the application is a HID device. Most of your own devices will be HID devices. But the virtual COM example uses a different USB class and in that program, the constant is set to 0.

&nbsp;

These constants are used in the add on to keep all code generic for all applications.

Since not all USB chips have the same options, the code also checks which microprocessor is used.

The USB1287 is a kind of M128 with USB support. It supports host and device mode. The USB162 is a cheap host chip. It does not support the HOST mode and it does not have all registers found in the USB1287. It also can not detect when a device is plugged/unplugged.

Atmel solved this in the STK526 in a simple way that we recommend too&nbsp;: A voltage divider is connected to PORTC.4 which serves as a simple way to detect plug/unplug.

In the USB_TASK() routine you will find this code&nbsp;:

&nbsp;

<span style="font-weight: bold;">If Usb_connected = 0 And Pinc.4 = 1 Then &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;' portc.4 is used as vbus detection on stk526</span>

&nbsp;

This is used with the STK526. If you want to use a different pin, you have to change PINC.4.

When you use the USB1287 this is not needed since the 1287 has a Usbsta register which can determine if a device is plugged or removed.

&nbsp;

The USB program structure is always the same&nbsp;:
<div style="padding: 0px; margin: 0px;">
{| border="0" cellpadding="0" cellspacing="0"
|- valign="baseline" style="vertical-align: baseline;"
| width="15" | <span style="font-size: 10pt;">1.</span>
| constants are defined that describe the end points, interfaces, vendor ID, product ID
|}
</div><div style="padding: 0px; margin: 0px;">
{| border="0" cellpadding="0" cellspacing="0"
|- valign="baseline" style="vertical-align: baseline;"
| width="15" | <span style="font-size: 10pt;">2.</span>
| you call a subroutine that initializes your variables
|}
</div><div style="padding: 0px; margin: 0px;">
{| border="0" cellpadding="0" cellspacing="0"
|- valign="baseline" style="vertical-align: baseline;"
| width="15" | <span style="font-size: 10pt;">3.</span>
| In a loop you call&nbsp;:
|}
</div><div style="padding: 0px; margin: 0px;">
{| border="0" cellpadding="0" cellspacing="0"
|- valign="baseline" style="vertical-align: baseline;"
| width="15" | <span style="font-size: 10pt;">4.</span>
| the generic USB_TASK routine so that the USB communication with the PC is executed
|}
</div><div style="padding: 0px; margin: 0px;">
{| border="0" cellpadding="0" cellspacing="0"
|- valign="baseline" style="vertical-align: baseline;"
| width="15" | <span style="font-size: 10pt;">5.</span>
| the specific task is called
|}
</div><div style="padding: 0px; margin: 0px;">
{| border="0" cellpadding="0" cellspacing="0"
|- valign="baseline" style="vertical-align: baseline;"
| width="15" | <span style="font-size: 10pt;">6.</span>
| your other code is called
|}
</div>
&nbsp;

This is clear in the keyboard sample&nbsp;:

&nbsp;

Print "init usb task"

Usb_task_init

Do

Usb_task

Kbd_task

'call your other code here

Loop

&nbsp;

While the word Task might give you the idea that multi task switching is used, this is not the case! The USB_Task must be called by your code in order to process pending USB events. It will also find out if a device is plugged or unplugged. Events are handled in the background by the&nbsp;<span style="font-weight: bold;">Usb_gen_int</span>&nbsp;interrupt.

In the example the KBD_TASK is a user routine which is called in regular intervals. There is always the normal USB_TASK and there is an additional task specific to the program. In the generic-hid example this is the hid_task routine.

&nbsp;

HID classes are simple to use since they do not require additional drivers. FTDI chips need additional drivers. But the Atmel USB chips do not need additional drivers since they use standard implemented HID classes.

&nbsp;

When you compile the program and program it into a chip you are ready to test it.

When you use FLIP you need to switch to application mode so your device can be recognized by windows. Windows will show some info that your device is found. And after installing the driver, it will report that your device is ready to be used.

On the terminal emulator, press a space, and set the focus to notepad or the bascom editor. The text data from the<span style="font-weight: bold;">keys</span>: label is send as if it was typed on a keyboard! You in fact created a HID-keyboard, or USB keyboard. The document translatePS2-HID.pdf contains HID key codes which are different then PS2 key scan codes.

&nbsp;

When you do not have a terminal emulator connected you can also modify the program and connect a push button. Which makes more sense for a keyboard&nbsp;:-)

So modify the code into&nbsp;: &nbsp;If Inkey() = 32 Or Pinb.0 = 0 Then 'if you press SPACE BAR or make PINB.0 low

Now you can test the code without the terminal emulator.

&nbsp;

&nbsp;

All USB programs are similar. You specify the number of end points , the interfaces and the class. There is a lot of information available at

[http://www.usb.org/home http://www.usb.org/home]

Atmel has a number of samples and you will find tools and info at various places.

MCS will publish some convenient tools too.

&nbsp;

= <span class="f_Header">FLIP</span> =

The USB chips are programmed with a boot loader. This is very convenient since you do not need any hardware to program the chip. FLIP can be downloaded from the Atmel site.

URL&nbsp;:&nbsp;<span style="font-family: Arial;">[http://www.atmel.com/dyn/resources/prod_documents/Flip%20Installer%20-%203.3.1.exe http://www.atmel.com/dyn/resources/prod_documents/Flip%20Installer%20-%203.3.1.exe]</span>

<span style="font-family: Arial;">The FLIP website you can find at&nbsp;:&nbsp;</span><span style="font-size: 12pt; font-family: 'Times New Roman'; color: rgb(0, 0, 255); text-decoration: underline;">[http://www.atmel.com/dyn/products/tools_card.asp?family_id=604&family_name=8051+Architecture&tool_id=3886 http://www.atmel.com/dyn/products/tools_card.asp?family_id=604&family_name=8051+Architecture&tool_id=3886]</span>

<span style="font-size: 12pt; font-family: 'Times New Roman'; color: rgb(0, 0, 255); text-decoration: underline;">&nbsp;</span>

<span style="font-family: Arial;">FLIP is a Java application. The BASCOM-IDE can use the FLIP software to program the chip too. But in order to use the FLIP programmer, you need to install FLIP first.</span>

<span style="font-family: Arial;">When FLIP is working, you can select FLIP from Options, Programmer, in order to program quickly without the FLIP executable.</span>

<span style="font-family: Arial;">On Vista there is a problem with loading some of the FLIP DLL's. In case you get an error, copy the FLIP DLL's to the BASCOM application directory.</span>

<span style="font-family: Arial;">You need to copy the following files&nbsp;:</span>
<div style="padding: 0px; margin: 0px;">
{| border="0" cellpadding="0" cellspacing="0"
|- valign="baseline" style="vertical-align: baseline;"
| width="13" | <span style="font-size: 10pt; font-family: 'Arial Unicode MS', 'Lucida Sans Unicode', Arial;">•</span>
| <span style="font-family: Arial;">atjniisp.dll</span>
|}
</div><div style="padding: 0px; margin: 0px;">
{| border="0" cellpadding="0" cellspacing="0"
|- valign="baseline" style="vertical-align: baseline;"
| width="13" | <span style="font-size: 10pt; font-family: 'Arial Unicode MS', 'Lucida Sans Unicode', Arial;">•</span>
| <span style="font-family: Arial;">AtLibUsbDfu.dll</span>
|}
</div><div style="padding: 0px; margin: 0px;">
{| border="0" cellpadding="0" cellspacing="0"
|- valign="baseline" style="vertical-align: baseline;"
| width="13" | <span style="font-size: 10pt; font-family: 'Arial Unicode MS', 'Lucida Sans Unicode', Arial;">•</span>
| <span style="font-family: Arial;">msvcp60.dll</span>
|}
</div><div style="padding: 0px; margin: 0px;">
{| border="0" cellpadding="0" cellspacing="0"
|- valign="baseline" style="vertical-align: baseline;"
| width="13" | <span style="font-size: 10pt; font-family: 'Arial Unicode MS', 'Lucida Sans Unicode', Arial;">•</span>
| <span style="font-family: Arial;">msvcrt.dll</span>
|}
</div>
<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">You can run the&nbsp;</span><span style="font-family: Arial; font-weight: bold;">flipDLLcopy.cmd</span><span style="font-family: Arial;">&nbsp;file from the BASCOM application directory to copy these files.</span>

<span style="font-family: Arial;">The content of the command file&nbsp;:</span>

<span style="font-family: Arial; font-style: italic;">copy "c:\program files\atmel\flip 3.3.1\bin\atjniisp.dll" .</span>

<span style="font-family: Arial; font-style: italic;">copy "c:\program files\atmel\flip 3.3.1\bin\AtLibUsbDfu.dll" .</span>

<span style="font-family: Arial; font-style: italic;">copy "c:\program files\atmel\flip 3.3.1\bin\msvcp60.dll" .</span>

<span style="font-family: Arial; font-style: italic;">copy "c:\program files\atmel\flip 3.3.1\bin\msvcrt.dll" .</span>

<span style="font-family: Arial; font-style: italic;">pause</span>

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">The last line pauses so you can view the result. &nbsp;Notice the . (dot) that will copy the file to the current directory, which is the reason that you need to run this file from the BASCOM application directory.</span>

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">As with other programmers, you press F4 to program the HEX file into the chip. A small window will become visible.</span>

<span style="font-family: Arial;">A number of dialogs are possible:</span>

<span style="font-family: Arial;">&nbsp;</span>

[[File:Flip error wrongdevice.png|center|flip_error_wrongdevice]]

<span style="font-family: Arial;">In this case, you try to program a chip which is not supported by FLIP. The Mega88 is not an USB chip so the error makes sense.</span>

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">The next dialog informs you about a missing DFU device.</span>

[[File:Flip reset.png|center|flip_reset]]

<span style="font-family: Arial;">In this case, the boot loader is not found. You can run the boot loader by following the sequence from the dialog box.</span>

<span style="font-family: Arial;">In order to make this work, the HWB and RST input both need a small switch to ground.</span>

<span style="font-family: Arial;">When HWB is pressed(low) during a reset, the boot loader will be executed.</span>

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">In the device manager you will find the USB device&nbsp;:</span>

<span style="font-family: Arial;">&nbsp;</span>

[[File:Usb dev manager.png|center|usb_dev_manager]]

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">When you have a different chip, a different device will be shown&nbsp;!</span>

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">When the programming succeeds, and there is no verify error, the application mode will be selected. This will disconnect the DFU and will connect your USB device&nbsp;!</span>

<span style="font-family: Arial;">&nbsp;</span>

[[File:Flip ok.png|center|flip_ok]]

<span style="font-family: Arial;">The FLIP programmer window will be closed automatic when the programming succeeds.</span>

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">The USB device will be shown&nbsp;:</span>

[[File:Usb device kb.png|center|usb_device_KB]]

<span style="font-family: Arial;">Since you created a keyboard device, the device will be shown under the KEYBOARDS node.</span>

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">When you load a generic HID device it will be shown under HUMAN INTERFACE DEVICES</span>

[[File:Usb generic.png|center|usb_generic]]

<span style="font-family: Arial;">&nbsp;</span>

= <span class="f_Header">HID Generic</span> =

<span style="font-family: Arial;">The generic HID class is the class that is well suited for transferring bytes between the PC and the micro processor.</span>

<span style="font-family: Arial;">As with any USB application, you specify the number of end points, The example just transfers 8 bytes in and 8 bytes out.</span>

<span style="font-family: Arial;">You need to change the Ep_in_length_1 , Ep_out_length, Length_of_report_in and Length_of_report_out constants when you want to transfer a different amount of bytes.</span>

<span style="font-family: Arial;">You also need to take into account the maximum data size which will depend on the used chip.</span>



<span style="font-family: Arial;">The&nbsp;</span><span style="font-family: Arial; font-weight: bold;">Usb_user_endpoint_init</span><span style="font-family: Arial;">&nbsp;sub routine also need to be adjusted. The size_8 constant specifies how many bytes are used by the endpoint.</span>

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">'init the user endpoints</span>

<span style="font-family: Arial;">Sub</span><span style="font-family: Arial; font-weight: bold;">&nbsp;Usb_user_endpoint_init</span><span style="font-family: Arial;">(byval Nm As Byte)</span>

<span style="font-family: Arial;">&nbsp;Call Usb_configure_endpoint(ep_hid_in , Type_interrupt , Direction_in , Size_8 , One_bank , Nyet_enabled)</span>

<span style="font-family: Arial;">&nbsp;Call Usb_configure_endpoint(ep_hid_out , Type_interrupt , Direction_out , Size_8 , One_bank , Nyet_enabled)</span>

<span style="font-family: Arial;">End Sub</span>

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">As with all USB program, we first initialize the USB task and the HID task. Then we call the tasks in a loop&nbsp;;</span>

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">Usb_task_init &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; ' init the usb task</span>

<span style="font-family: Arial;">Hid_task_init &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; ' init the USB task</span>

<span style="font-family: Arial;">Do</span>

<span style="font-family: Arial;">&nbsp;Usb_task &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;'call this subroutine once in a while</span>

<span style="font-family: Arial;">&nbsp;Hid_task &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;'call this subroutine once in a while</span>

<span style="font-family: Arial;">&nbsp;'you can call your sub program here</span>

<span style="font-family: Arial;">Loop</span>

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">The Hid_task itself is very simple&nbsp;:</span>

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">Sub&nbsp;</span><span style="font-family: Arial; font-weight: bold;">Hid_task</span><span style="font-family: Arial;">()</span>

<span style="font-family: Arial;">&nbsp; &nbsp;If Usb_connected = 1 Then &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; ' Check USB HID is enumerated</span>

<span style="font-family: Arial;">&nbsp; &nbsp; &nbsp; Usb_select_endpoint Ep_hid_out &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; ' Get Data Repport From Host</span>

<span style="font-family: Arial;">&nbsp; &nbsp; &nbsp; If Ueintx.rxouti = 1 Then &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; ' Is_usb_receive_out())</span>

<span style="font-family: Arial;">&nbsp; &nbsp; &nbsp; &nbsp; &nbsp;Dummy1 = Uedatx&nbsp;: Print "Got&nbsp;: "&nbsp;; Dummy1 &nbsp; &nbsp; &nbsp; &nbsp; ' it is important that you read the same amount of bytes here as were sent by the host&nbsp;!</span>

<span style="font-family: Arial;">&nbsp; &nbsp; &nbsp; &nbsp; &nbsp;Dummy2 = Uedatx&nbsp;: Print "Got&nbsp;: "&nbsp;; Dummy2</span>

<span style="font-family: Arial;">&nbsp; &nbsp; &nbsp; &nbsp; &nbsp;Dummy = Uedatx&nbsp;: Print "Got&nbsp;: "&nbsp;; Dummy</span>

<span style="font-family: Arial;">&nbsp; &nbsp; &nbsp; &nbsp; &nbsp;Dummy = Uedatx&nbsp;: Print "Got&nbsp;: "&nbsp;; Dummy</span>

<span style="font-family: Arial;">&nbsp; &nbsp; &nbsp; &nbsp; &nbsp;Dummy = Uedatx&nbsp;: Print "Got&nbsp;: "&nbsp;; Dummy</span>

<span style="font-family: Arial;">&nbsp; &nbsp; &nbsp; &nbsp; &nbsp;Dummy = Uedatx&nbsp;: Print "Got&nbsp;: "&nbsp;; Dummy</span>

<span style="font-family: Arial;">&nbsp; &nbsp; &nbsp; &nbsp; &nbsp;Dummy = Uedatx&nbsp;: Print "Got&nbsp;: "&nbsp;; Dummy</span>

<span style="font-family: Arial;">&nbsp; &nbsp; &nbsp; &nbsp; &nbsp;Dummy = Uedatx&nbsp;: Print "Got&nbsp;: "&nbsp;; Dummy</span>

<span style="font-family: Arial;">&nbsp; &nbsp; &nbsp; &nbsp; &nbsp;Usb_ack_receive_out</span>

<span style="font-family: Arial;">&nbsp; &nbsp; &nbsp;End If</span>

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">&nbsp; &nbsp; &nbsp;If Dummy1 = &H55 And Dummy2 = &HAA Then &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; ' Check if we received DFU mode command from host</span>

<span style="font-family: Arial;">&nbsp; &nbsp; &nbsp; &nbsp; Usb_detach &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; ' Detach Actual Generic Hid Application</span>

<span style="font-family: Arial;">&nbsp; &nbsp; &nbsp; &nbsp; Waitms 500</span>

<span style="font-family: Arial;">&nbsp; &nbsp; &nbsp; &nbsp; Goto &H1800 &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;'goto bootloader</span>

<span style="font-family: Arial;">&nbsp; &nbsp; &nbsp; &nbsp; 'here you could call the bootloader then</span>

<span style="font-family: Arial;">&nbsp; &nbsp; &nbsp;End If</span>

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">&nbsp; &nbsp; &nbsp;Usb_select_endpoint Ep_hid_in &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; ' Ready to send these information to the host application</span>

<span style="font-family: Arial;">&nbsp; &nbsp; &nbsp;If Ueintx.txini = 1 Then &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;' Is_usb_in_ready())</span>

<span style="font-family: Arial;">&nbsp; &nbsp; &nbsp; &nbsp; Uedatx = 1</span>

<span style="font-family: Arial;">&nbsp; &nbsp; &nbsp; &nbsp; Uedatx = 2</span>

<span style="font-family: Arial;">&nbsp; &nbsp; &nbsp; &nbsp; Uedatx = 3</span>

<span style="font-family: Arial;">&nbsp; &nbsp; &nbsp; &nbsp; Uedatx = 4</span>

<span style="font-family: Arial;">&nbsp; &nbsp; &nbsp; &nbsp; Uedatx = 5</span>

<span style="font-family: Arial;">&nbsp; &nbsp; &nbsp; &nbsp; Uedatx = 6</span>

<span style="font-family: Arial;">&nbsp; &nbsp; &nbsp; &nbsp; Uedatx = 7</span>

<span style="font-family: Arial;">&nbsp; &nbsp; &nbsp; &nbsp; Uedatx = 8</span>

<span style="font-family: Arial;">&nbsp; &nbsp; &nbsp; &nbsp; Usb_ack_fifocon &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;' Send data over the USB</span>

<span style="font-family: Arial;">&nbsp; &nbsp; &nbsp;End If</span>

<span style="font-family: Arial;">&nbsp; &nbsp;End If</span>

<span style="font-family: Arial;">End Sub</span>

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">We first check if the device is connected to the USB bus. Then we use&nbsp;</span><span style="font-family: Arial; font-weight: bold;">Usb_select_endpoint</span><span style="font-family: Arial;">&nbsp;with the number of the end point, to select the end point.</span>

<span style="font-family: Arial;">When we want to communicate with an end point, we always have to select this end point using the&nbsp;</span><span style="font-family: Arial; font-weight: bold;">Usb_select_endpoint</span><span style="font-family: Arial;">&nbsp;procedure.</span>

<span style="font-family: Arial;">In the sample, we first select the EP_HID_OUT end point. We check the UEINTX.RXOUTI flag to determine if we received an interrupt with data. If that is the case, we read the UEDATX register to read the data byte.</span>

<span style="font-family: Arial;">The UEDATX register is the USB data register. When you read it, you read data from the USB bus. When you write it, you write data to the USB bus.</span>

<span style="font-family: Arial;">After reading the bytes you MUST acknowledge with the&nbsp;</span><span style="font-family: Arial; font-weight: bold;">Usb_ack_receive_out</span><span style="font-family: Arial;">&nbsp;macro.</span>

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">The sample also shows how to run the boot loader from your code. In order to run the boot loader you must detach the current device from the USB bus. Then there is some delay to have windows process it. Finally the GOTO jumps to the boot loader address of the USB162.</span>

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">If you want to write some data back, you need to select the end point, and check if you may send data. If that is the case, you assign the data to the UEDATX register and finally, you MUST acknowledge with the USB_ACK_FIFOCON macro.</span>

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">Finally, you will find in the report data the length of the end points specified&nbsp;: Data &H75 , &H08 &nbsp;</span>

<span style="font-family: Arial;">You need to adjust these values when you want to send/receive more data.</span>

<span style="font-family: Arial;">&nbsp;</span>

= <span class="f_Header">HIDX.OCX</span> =

<span style="font-family: Arial;">There are plenty of examples on the internet that show how to communicate with HID devices using the windows API.</span>

<span style="font-family: Arial;">The HIDX.OCX is an OCX control that can be used for simple communication.</span>

<span style="font-family: Arial;">Like all OCX controls, you must register it first with REGSVR32 &nbsp; &nbsp;: &nbsp; regsvr32 hidx.ocx</span>

<span style="font-family: Arial;">After it has been registered you can run the VB test application named HIDdemo.exe.</span>

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">The application will list all HID devices&nbsp;:</span>

<span style="font-family: Arial;">&nbsp;</span>

[[File:Hid ocx1.png|center|hid_ocx1]]

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">Our device is the device with VID 16D0 and PID 201D.</span>

<span style="font-family: Arial;">There can only be one application/process at the time that communicates with an USB device.</span>

<span style="font-family: Arial;">You must click the checkout-button the device to start communication. This will call the&nbsp;</span><span style="font-family: Arial; font-weight: bold;">SelectDevice</span><span style="font-family: Arial;">&nbsp;method of the OCX.</span>

<span style="font-family: Arial;">As soon as you do this, you will notice that the&nbsp;</span><span style="font-family: Arial; font-weight: bold;">OnDataRead</span><span style="font-family: Arial;">&nbsp;event will receive data.</span>

<span style="font-family: Arial;">&nbsp;</span>

[[File:Hid ocx2.png|center|hid_ocx2]]

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">The event has the following parameters&nbsp;:</span>

<span style="font-family: Arial;">(ByVal Device As Long, ByVal ReportID As Long, ByVal Data As String, ByVal Size As Long)</span>

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">The device is a number with the index of all HID devices. The first device will have number 0. The report number is passed in ReportID. The data is passed as a string.</span>

<span style="font-family: Arial;">You can use MID to access this data&nbsp;: firstByte= Asc(Mid(data,1,1))</span>

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">To write to the device, you can use the&nbsp;</span><span style="font-family: Arial; font-weight: bold;">WriteDevice</span><span style="font-family: Arial;">&nbsp;method. The same parameters are used as with the OnDataRead event.</span>

<span style="font-family: Arial;">Example&nbsp;: WriteDevice curdev, 0, s, 8</span>

<span style="font-family: Arial;">Curdev is the index of the device. 0 is the report ID and s contains the data. You must specify the length of the data to send.</span>

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">To stop communication you can click the Checkin-button.This will call the&nbsp;</span><span style="font-family: Arial; font-weight: bold;">ReleaseDevice</span><span style="font-family: Arial;">&nbsp;method.</span>

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">When the device changes, or will be removed or inserted, you will receive a notification.</span>

<span style="font-family: Arial;">In the sample program, all these events will result in a release of the device. This is done since the curdev variable can change when a new device is added. The index will not correspond to the existing index then anymore. The sample is very simple. In an application you could add a function or procedure that will examine the new list of devices and return the index of our device. When our device is found we could open it automatic again.</span>

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">Notice that you can not add too much lines to a listbox in VB. Since data arrives at a very high rate, it will not take long before VB/Windows will give some error.</span>

<span style="font-family: Arial;">&nbsp;</span>
<div style="padding: 0px; margin: 0px;">
{| cellspacing="0" cellpadding="0" border="0" style="border: none; border-spacing: 0px; border-collapse: collapse;"
|- style="vertical-align: top;"
| valign="top" width="206" bgcolor="#ffff99" style="width: 206px; background-color: rgb(255, 255, 153); border-style: solid; border-color: rgb(0, 0, 0);" | <p style="text-align: center;"><span style="font-weight: bold;">Property</span></p>
| valign="top" width="620" bgcolor="#ffff99" style="width: 620px; background-color: rgb(255, 255, 153); border-style: solid; border-color: rgb(0, 0, 0);" | <p style="text-align: center;"><span style="font-weight: bold;">Description</span></p>
|- style="vertical-align: top;"
| valign="top" width="206" style="width: 206px; border-style: solid; border-color: rgb(0, 0, 0);" | 
NumCheckedInDevices

| valign="top" width="620" style="width: 620px; border-style: solid; border-color: rgb(0, 0, 0);" | 
Number of &nbsp;available devices

|- style="vertical-align: top;"
| valign="top" width="206" style="width: 206px; border-style: solid; border-color: rgb(0, 0, 0);" | 
NumCheckedOutDevices

| valign="top" width="620" style="width: 620px; border-style: solid; border-color: rgb(0, 0, 0);" | 
Number of devices that are checked out and communicating.

|- style="vertical-align: top;"
| valign="top" width="206" style="width: 206px; border-style: solid; border-color: rgb(0, 0, 0);" | 
NumUnpluggedDevices

| valign="top" width="620" style="width: 620px; border-style: solid; border-color: rgb(0, 0, 0);" | <br/>
|- style="vertical-align: top;"
| valign="top" width="206" style="width: 206px; border-style: solid; border-color: rgb(0, 0, 0);" | 
DevThreadSleepTime

| valign="top" width="620" style="width: 620px; border-style: solid; border-color: rgb(0, 0, 0);" | 
The time in mS that the HID thread will sleep. You can see this as a timer interval. The lower the interval the more process time it will take. 100 mS is a good value for most applications.

|- style="vertical-align: top;"
| valign="top" width="206" style="width: 206px; border-style: solid; border-color: rgb(0, 0, 0);" | 
Version

| valign="top" width="620" style="width: 620px; border-style: solid; border-color: rgb(0, 0, 0);" | 
The version of the control

|- style="vertical-align: top;"
| valign="top" width="206" style="width: 206px; border-style: solid; border-color: rgb(0, 0, 0);" | 
DeviceCount

| valign="top" width="620" style="width: 620px; border-style: solid; border-color: rgb(0, 0, 0);" | 
The number of devices.

|- style="vertical-align: top;"
| valign="top" width="206" style="width: 206px; border-style: solid; border-color: rgb(0, 0, 0);" | <br/>
| valign="top" width="620" style="width: 620px; border-style: solid; border-color: rgb(0, 0, 0);" | <br/>
|-
| width="206" bgcolor="#ffff99" style="width: 206px; background-color: rgb(255, 255, 153); border-style: solid; border-color: rgb(0, 0, 0);" | <p style="text-align: center;"><span style="font-weight: bold;">Methods</span></p>
| width="620" bgcolor="#ffff99" style="width: 620px; background-color: rgb(255, 255, 153); border-style: solid; border-color: rgb(0, 0, 0);" | <br/>
|- style="vertical-align: top;"
| valign="top" width="206" style="width: 206px; border-style: solid; border-color: rgb(0, 0, 0);" | 
SelectDevice

| valign="top" width="620" style="width: 620px; border-style: solid; border-color: rgb(0, 0, 0);" | 
Parameters
<div style="padding: 0px; margin: 0px;">
{| border="0" cellpadding="0" cellspacing="0"
|- valign="baseline" style="vertical-align: baseline;"
| width="13" | <span style="font-size: 10pt; font-family: 'Arial Unicode MS', 'Lucida Sans Unicode', Arial;">•</span>
| Device&nbsp;: LONG that specifies the index of the device to select. The index starts at 0.
|}
</div>
|- style="vertical-align: top;"
| valign="top" width="206" style="width: 206px; border-style: solid; border-color: rgb(0, 0, 0);" | 
ReleaseDevice

| valign="top" width="620" style="width: 620px; border-style: solid; border-color: rgb(0, 0, 0);" | 
Parameters
<div style="padding: 0px; margin: 0px;">
{| border="0" cellpadding="0" cellspacing="0"
|- valign="baseline" style="vertical-align: baseline;"
| width="13" | <span style="font-size: 10pt; font-family: 'Arial Unicode MS', 'Lucida Sans Unicode', Arial;">•</span>
| Device&nbsp;: LONG that specifies the index of the device to release. The index starts at 0.
|}
</div>
|- style="vertical-align: top;"
| valign="top" width="206" style="width: 206px; border-style: solid; border-color: rgb(0, 0, 0);" | 
WriteDevice

| valign="top" width="620" style="width: 620px; border-style: solid; border-color: rgb(0, 0, 0);" | 
Parameters
<div style="padding: 0px; margin: 0px;">
{| border="0" cellpadding="0" cellspacing="0"
|- valign="baseline" style="vertical-align: baseline;"
| width="13" | <span style="font-size: 10pt; font-family: 'Arial Unicode MS', 'Lucida Sans Unicode', Arial;">•</span>
| Device&nbsp;: LONG that specifies the index of the device to write to. The index starts at 0.
|}
</div><div style="padding: 0px; margin: 0px;">
{| border="0" cellpadding="0" cellspacing="0"
|- valign="baseline" style="vertical-align: baseline;"
| width="13" | <span style="font-size: 10pt; font-family: 'Arial Unicode MS', 'Lucida Sans Unicode', Arial;">•</span>
| Report&nbsp;: LONG that specifies the report number. This would be 0 in most cases.
|}
</div><div style="padding: 0px; margin: 0px;">
{| border="0" cellpadding="0" cellspacing="0"
|- valign="baseline" style="vertical-align: baseline;"
| width="13" | <span style="font-size: 10pt; font-family: 'Arial Unicode MS', 'Lucida Sans Unicode', Arial;">•</span>
| Data&nbsp;: string that contains the data to send.
|}
</div><div style="padding: 0px; margin: 0px;">
{| border="0" cellpadding="0" cellspacing="0"
|- valign="baseline" style="vertical-align: baseline;"
| width="13" | <span style="font-size: 10pt; font-family: 'Arial Unicode MS', 'Lucida Sans Unicode', Arial;">•</span>
| Size&nbsp;: the length of the data to send.
|}
</div>
&nbsp;

&nbsp;

|- style="vertical-align: top;"
| valign="top" width="206" style="width: 206px; border-style: solid; border-color: rgb(0, 0, 0);" | <br/>
| valign="top" width="620" style="width: 620px; border-style: solid; border-color: rgb(0, 0, 0);" | <br/>
|-
| width="206" bgcolor="#ffff99" style="width: 206px; background-color: rgb(255, 255, 153); border-style: solid; border-color: rgb(0, 0, 0);" | <p style="text-align: center;"><span style="font-weight: bold;">Events</span></p>
| width="620" bgcolor="#ffff99" style="width: 620px; background-color: rgb(255, 255, 153); border-style: solid; border-color: rgb(0, 0, 0);" | <br/>
|- style="vertical-align: top;"
| valign="top" width="206" style="width: 206px; border-style: solid; border-color: rgb(0, 0, 0);" | 
OnDeviceChange

| valign="top" width="620" style="width: 620px; border-style: solid; border-color: rgb(0, 0, 0);" | 
Parameters
<div style="padding: 0px; margin: 0px;">
{| border="0" cellpadding="0" cellspacing="0"
|- valign="baseline" style="vertical-align: baseline;"
| width="13" | <span style="font-size: 10pt; font-family: 'Arial Unicode MS', 'Lucida Sans Unicode', Arial;">•</span>
| none.
|}
</div>
&nbsp;

This event fires when a device changes. This can be because a new device is added, or a device is removed.

|- style="vertical-align: top;"
| valign="top" width="206" style="width: 206px; border-style: solid; border-color: rgb(0, 0, 0);" | 
OnDeviceArrival

| valign="top" width="620" style="width: 620px; border-style: solid; border-color: rgb(0, 0, 0);" | 
Parameters
<div style="padding: 0px; margin: 0px;">
{| border="0" cellpadding="0" cellspacing="0"
|- valign="baseline" style="vertical-align: baseline;"
| width="13" | <span style="font-size: 10pt; font-family: 'Arial Unicode MS', 'Lucida Sans Unicode', Arial;">•</span>
| Device&nbsp;: LONG that specifies the index of the device that arrived. The index starts at 0.
|}
</div>
&nbsp;

This event fires when a device is inserted. When a device is added or removed, the index that was used previously, does not need to match the new index anymore. For this reason you have to checkout the device again.

|- style="vertical-align: top;"
| valign="top" width="206" style="width: 206px; border-style: solid; border-color: rgb(0, 0, 0);" | 
OnDeviceRemoval

| valign="top" width="620" style="width: 620px; border-style: solid; border-color: rgb(0, 0, 0);" | 
Parameters
<div style="padding: 0px; margin: 0px;">
{| border="0" cellpadding="0" cellspacing="0"
|- valign="baseline" style="vertical-align: baseline;"
| width="13" | <span style="font-size: 10pt; font-family: 'Arial Unicode MS', 'Lucida Sans Unicode', Arial;">•</span>
| Device&nbsp;: LONG that specifies the index of the device that has been removed. The index starts at 0.
|}
</div>
&nbsp;

This event fires when a device is removed. When a device is added or removed, the index that was used previously, does not need to match the new index anymore. For this reason you have to checkout the device again.

|- style="vertical-align: top;"
| valign="top" width="206" style="width: 206px; border-style: solid; border-color: rgb(0, 0, 0);" | 
OnDataRead

| valign="top" width="620" style="width: 620px; border-style: solid; border-color: rgb(0, 0, 0);" | 
Parameters
<div style="padding: 0px; margin: 0px;">
{| border="0" cellpadding="0" cellspacing="0"
|- valign="baseline" style="vertical-align: baseline;"
| width="13" | <span style="font-size: 10pt; font-family: 'Arial Unicode MS', 'Lucida Sans Unicode', Arial;">•</span>
| Device&nbsp;: LONG that specifies the index of the device that sent data. The index starts at 0.
|}
</div><div style="padding: 0px; margin: 0px;">
{| border="0" cellpadding="0" cellspacing="0"
|- valign="baseline" style="vertical-align: baseline;"
| width="13" | <span style="font-size: 10pt; font-family: 'Arial Unicode MS', 'Lucida Sans Unicode', Arial;">•</span>
| ReportID&nbsp;: LONG with the report ID of the device that sent the data.
|}
</div><div style="padding: 0px; margin: 0px;">
{| border="0" cellpadding="0" cellspacing="0"
|- valign="baseline" style="vertical-align: baseline;"
| width="13" | <span style="font-size: 10pt; font-family: 'Arial Unicode MS', 'Lucida Sans Unicode', Arial;">•</span>
| Data&nbsp;: string that contains the data. This string might contain 0-bytes.
|}
</div><div style="padding: 0px; margin: 0px;">
{| border="0" cellpadding="0" cellspacing="0"
|- valign="baseline" style="vertical-align: baseline;"
| width="13" | <span style="font-size: 10pt; font-family: 'Arial Unicode MS', 'Lucida Sans Unicode', Arial;">•</span>
| Size&nbsp;: LONG that contains the length of the received data.
|}
</div>
&nbsp;

When data is received you can read it in this event. For example&nbsp;:

dim ar(8) as Byte

For J=1 to Size

ar(j) = ASC(Mid(data,J,1)) ' fill the array

Next

&nbsp;

|- style="vertical-align: top;"
| valign="top" width="206" style="width: 206px; border-style: solid; border-color: rgb(0, 0, 0);" | 
&nbsp;

| valign="top" width="620" style="width: 620px; border-style: solid; border-color: rgb(0, 0, 0);" | <br/>
|}
</div>
<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">The OCX can be used with all programming languages that can host OCX controls. The OCX was tested with Delphi and VB.</span>

<span style="font-family: Arial;">Your windows must support USB in order to use the OCX. So it will not work on Windows 95.</span>

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">&nbsp;</span>

= <span class="f_Header">Virtual COM sample</span> =

<span style="font-family: Arial;">The virtual COM demo shows how to implement an USB device with a virtual COM port. The Demo will echo data sent to the UART to the USB and vise versa.</span>

<span style="font-family: Arial;">When you compile and program the sample, you will notice that you find a new COM port in the device manager.</span>

[[File:Notice.jpg|notice]]<span style="font-family: Arial;">When you press CTRL+D, BASCOM will launch the device manager.</span>

<span style="font-family: Arial;">&nbsp;</span>

[[File:Dev mng.png|center|dev_mng]]

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">As you can see, the CDC class is used for the virtual COM port. As with most virtual COM devices, you can change the settings&nbsp;:</span>

<span style="font-family: Arial;">&nbsp;</span>

[[File:Virtual com.png|center|virtual COM]]

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">In the BASCOM application the procedure Cdc_get_line_coding is called when the PC need to know the settings.</span>

<span style="font-family: Arial;">The Cdc_set_line_coding is called when the settings are changed by the user. You need to change the settings according to the received parameters.</span>

<span style="font-family: Arial;">Notice that these settings are virtual too&nbsp;: for the USB it does not matter how the baud rate is set&nbsp;! Only for a real UART this is important. For an USB-RS232 converter for example it is very convenient to be able to change the baud rate and other settings. But when you just use the USB port for communication, and choose to use the COM port in your program as a way for communication, then you do not really need the settings.</span>

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">When you want to send date to the USB/COM you can use the&nbsp;</span><span style="font-family: Arial; font-weight: bold;">Uart_usb_putchar</span><span style="font-family: Arial;">&nbsp;procedure. Like any USB routine, it will select the proper end point. After the end point for sending data is selected it will wait if it may send data, and finally it will send this data.</span>

<span style="font-family: Arial;">The&nbsp;</span><span style="font-family: Arial; font-weight: bold;">Uart_usb_getchar</span><span style="font-family: Arial;">() function can be used to receive data from the USB/COM.</span>

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">When you create your own device, the virtual COM port has the advantage that the PC application is simple. In most cases you already have the experience to read/write data to the PC COM port.</span>

<span style="font-family: Arial;">The disadvantage is that it requires mode code. It also need an INF file. This INF file you can change to suite your own needs.</span>

<span style="font-family: Arial;">When you create your own device, the HID device is the simplest way to go.</span>

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">&nbsp;</span>

<span style="font-family: Arial;">&nbsp;</span>

= <span class="f_Header">CDC INF file</span> =

<span style="font-family: Arial;">The CDC INF file looks like this. The bold parts need to be changed if you want to customize with your own text and VID/PID.</span>

<span style="font-family: Arial;">&nbsp;</span> <source lang="reg">
; Windows 2000, XP & Vista setup File for AT90USBxx2 demo
 
[Version]
Signature="$Windows NT$"
Class=Ports
ClassGuid={4D36E978-E325-11CE-BFC1-08002BE10318}
 
Provider=%ATMEL%
LayoutFile=layout.inf
DriverVer=10/15/1999,5.0.2153.1
 
[Manufacturer]
%ATMEL%=ATMEL
 
[ATMEL]
%ATMEL_CDC%=Reader, USB\VID_03EB&PID_2018
 
 
[Reader_Install.NTx86]
;Windows2000
 
[DestinationDirs]
DefaultDestDir=12
Reader.NT.Copy=12
 
[Reader.NT]
include=mdmcpq.inf
CopyFiles=Reader.NT.Copy
AddReg=Reader.NT.AddReg
 
[Reader.NT.Copy]
usbser.sys
 
[Reader.NT.AddReg]
HKR,,DevLoader,,*ntkern
HKR,,NTMPDriver,,usbser.sys
HKR,,EnumPropPages32,,"MsPorts.dll,SerialPortPropPageProvider"
 
[Reader.NT.Services]
AddService = usbser, 0x00000002, Service_Inst
 
[Service_Inst]
DisplayName = %Serial.SvcDesc%
ServiceType = 1 ; SERVICE_KERNEL_DRIVER
StartType = 3 ; SERVICE_DEMAND_START
ErrorControl = 1 ; SERVICE_ERROR_NORMAL
ServiceBinary = %12%\usbser.sys
LoadOrderGroup = Base
 
[Strings]
ATMEL = "ATMEL, Inc."
ATMEL_CDC = "AT90USBxxx CDC USB to UART MGM"
Serial.SvcDesc = "USB Serial emulation driver"
 
;---- END OF INF FILE
</source> {{Languages}}

[[Category:USB/de]]