GETDSTPORT/de

= (**COPIED FROM ENGLISH PAGE**) === Action

Returns the port number of the peer.

 

 

Syntax

Result = GETDSTPort( socket)

 

 

Remarks

Result	A WORD variable that is assigned with the port number of the peer or destination port number.
Socket	The socket number in the range from 0-3

 

When you are in server mode, it might be desirable to detect the port number of the connecting client.

You can use this for logging, security, etc.

 

 

See also

CONFIG TCPIP, GETSOCKET , SOCKETCONNECT, SOCKETSTAT , TCPWRITE, TCPWRITESTR, CLOSESOCKET ,SOCKETLISTEN , GETDSTIP

 

 

 

Example

'-----------------------------------------------------------------------------------------
'name : servertest_TWI.bas
'copyright : (c) 1995-2012, MCS Electronics
'purpose : start the easytcp after the chip is programmed
' and create 2 connections
'micro : Mega88
'suited for demo : no
'commercial addon needed : yes
'-----------------------------------------------------------------------------------------
 
$regfile = "m88def.dat" ' specify the used micro
$crystal = 8000000 ' used crystal frequency
$baud = 19200 ' use baud rate
 
$hwstack = 128 ' default use 32 for the hardware stack
$swstack = 128 ' default use 10 for the SW stack
$framesize = 128 ' default use 40 for the frame space
 ' xram access
Print "Init , set IP to 192.168.1.70" ' display a message
Enable Interrupts ' before we use config tcpip , we need to enable the interrupts
Config Tcpip = Int1 , Mac = 12.128.12.34.56.78 , Ip = 192.168.1.70 , Submask = 255.255.255.0 , Gateway = 192.168.1.1 , Localport = 1000 , Tx = $55 , Rx = $55 , Chip = W5100 , Spi = 1
 
 
Dim Bclient As Byte ' socket number
Dim Idx As Byte
Dim Result As Word , Result2 As Word ' result
Dim S As String * 80
Dim Flags As Byte
Dim Peer As Long
Dim L As Long
 
 
Do
Waitms 1000
For Idx = 0 To 3
 Result = Socketstat(idx , 0) ' get status
 Select Case Result
 Case Sock_established
 If Flags.idx = 0 Then ' if we did not send a welcome message yet
 Flags.idx = 1
 Result = Tcpwrite(idx , "Hello from W3100A{013}{010}") ' send welcome
 End If
 Result = Socketstat(idx , Sel_recv) ' get number of bytes waiting
 Print "Received : " ; Result
 If Result > 0 Then
 Do
 Print "Result : " ; Result
 Result = Tcpread(idx , S)
 Print "Data from client: " ; Idx ; " " ; Result ; " " ; S
 Peer = Getdstip(idx)
 Print "Peer IP " ; Ip2str(peer)
 Print "Peer port : " ; Getdstport(idx)
 'you could analyse the string here and send an appropiate command
 'only exit is recognized
 If Lcase(s) = "exit" Then
 Closesocket Idx
 Elseif Lcase(s) = "time" Then
 Result2 = Tcpwrite(idx , "12:00:00{013}{010}") ' you should send date$ or time$
 End If
 Loop Until Result = 0
 End If
 Case Sock_close_wait
 Print "close_wait"
 Closesocket Idx
 Case Sock_closed
 Print "closed"
 Bclient = Getsocket(idx , Sock_stream , 5000 , 64) ' get socket for server mode, specify port 5000
 Print "Socket " ; Idx ; " " ; Bclient
 
 Socketlisten Idx
 Print "Result " ; Result
 Flags.idx = 0 ' reset the hello message flag
 Case Sock_listen 'this is normal
 Case Else
 Print "Socket status : " ; Result
 End Select
Next
Loop
 
 
 
End

Languages	English • Deutsch