SONYSEND/de

= (**COPIED FROM ENGLISH PAGE**) === Action

Sends Sony remote IR code.

 

 

Syntax

SONYSEND address [, bits]

 

 

Uses

TIMER1

 

 

Remarks

Address	The address of the Sony device.
bits	This is an optional parameter. When used, it must be 12, 15 or 20.   Also, when you use this option, the address variable must be of the type LONG.

 

 

SONY CD Infrared Remote Control codes (RM-DX55)

Function	Hex	Bin
Power	A91	1010 1001 0001
Play	4D1	0100 1101 0001
Stop	1D1	0001 1101 0001
Pause	9D1	1001 1101 0001
Continue	B91	1011 1001 0001
Shuffle	AD1	1010 1101 0001
Program	F91	1111 1001 0001
Disc	531	0101 0011 0001
1	011	0000 0001 0001
2	811	1000 0001 0001
3	411	0100 0001 0001
4	C11	1100 0001 0001
5	211	0010 0001 0001
6	A11	1010 0001 0001
7	611	0110 0001 0001
8	E11	1110 0001 0001
9	111	0001 0001 0001
0	051	0000 0101 0001
>10	E51	1110 0101 0001
enter	D11	1101 0001 0001
clear	F11	1111 0001 0001
repeat	351	0011 0101 0001
disc -	BD1	1011 1101 0001
disc +	H7D1	0111 1101 0001
|<<	0D1	0000 1101 0001
>>|	8D1	1000 1101 0001
<<	CD1	1100 1101 0001
>>	2D1	0010 1101 0001
SONY Cassette	RM-J901)
Deck A
stop	1C1	0001 1100 0001
play >	4C1	0100 1100 0001
play <	EC1	1110 1100 0001
>>	2C1	0010 1100 0001
<<	CC1	1100 1100 0001
record	6C1	0110 1100 0001
pause	9C1	1001 1100 0001
Dec B
stop	18E	0001 1000 1110
play >	58E	0101 1000 1110
play <	04E	0000 0100 1110
>>	38E	0011 1000 1110
<<	D8E	1101 1000 1110
record	78E	0111 1000 1110
pause	98E	1001 1000 1110

 

 

---[ SONY TV Infrared Remote Control codes (RM-694) ]--------------------------

 

program + = &H090 : 0000 1001 0000

program - = &H890 : 1000 1001 0000

volume + = &H490 : 0100 1001 0000

volume - = &HC90 : 1100 1001 0000

power = &HA90 : 1010 1001 0000

sound on/off = &H290 : 0010 1001 0000

1 = &H010 : 0000 0001 0000

2 = &H810 : 1000 0001 0000

3 = &H410 : 0100 0001 0000

4 = &HC10 : 1100 0001 0000

5 = &H210 : 0010 0001 0000

6 = &HA10 : 1010 0001 0000

7 = &H610 : 0110 0001 0000

8 = &HE10 : 1110 0001 0000

9 = &H110 : 0001 0001 0000

0 = &H910 : 1001 0001 0000

-/-- = &HB90 : 1011 1001 0000

 

 

For more SONY Remote Control info:

http://www.fet.uni-hannover.de/purnhage/

 

 

The resistor must be connected to the OC1A pin. In the example a 2313 micro was used. This micro has pin portB.3 connected to OC1A.

Look in a data sheet for the proper pin when used with a different chip.

 

An IR booster circuit is shown below:

 

 

 

When sending hex, prefix with &H. When sending binary data, prefix with &B.

Sonysend &HA90

Sonysend &B010011010001

 

 

See also

CONFIG RC5 , GETRC5 , RC5SEND , RC6SEND

 

 

Example

'-----------------------------------------------------------------------------------------
'name : sonysend.bas
'copyright : (c) 1995-2005, MCS Electronics
'purpose : code based on application note from Ger Langezaal
'micro : AT90S2313
'suited for demo : yes
'commercial addon needed : no
'-----------------------------------------------------------------------------------------
 
$regfile = "2313def.dat" ' specify the used micro
$crystal = 4000000 ' used crystal frequency
$baud = 19200 ' use baud rate
$hwstack = 32 ' default use 32 for the hardware stack
$swstack = 10 ' default use 10 for the SW stack
$framesize = 40 ' default use 40 for the frame space
 
 
' +5V <---[A Led K]---[220 Ohm]---> Pb.3 for 2313.
' RC5SEND is using TIMER1, no interrupts are used
' The resistor must be connected to the OC1(A) pin , in this case PB.3
 
Do
Waitms 500
Sonysend &HA90
Loop
End

Languages	English • Deutsch